Ask Experts Questions for FREE Help !
Ask
    linzyxo's Avatar
    linzyxo Posts: 2, Reputation: 1
    New Member
     
    #1

    Apr 22, 2007, 03:54 PM
    Copper Pipe Threads leaking
    I just installed a new shower regulator after moving the copper piping. The solder joints are holding but the threads on one side of the regulator are seeping (about 1 drip a min). Looks like the teflon tape missed a thread to two... I can't take it apart and try again because it's affixed to the wall and soldered in tightly to the other two connections. And I can't seal the wall until we fix the drip (and know it's fixed for good).

    I went to home depot and found three products and can't decided on which one to use. Two are epoxies (locktite marine epoxy and NSF Plumbing Epoxy Putty). The other is like super glue but better apparently. Called Amazing Goop for plumbing it claims to be a waterproof contact adhesive and sealant.

    Any experience with any of these or recommendations on what might work? Thanks!
    TheSavage's Avatar
    TheSavage Posts: 564, Reputation: 96
    Senior Member
     
    #2

    Apr 22, 2007, 04:01 PM
    Personally --if was me, I would not trust any goop- I think as much of a pain in the butt as it is you need to fix it right.
    speedball1's Avatar
    speedball1 Posts: 29,301, Reputation: 1939
    Eternal Plumber
     
    #3

    Apr 22, 2007, 04:20 PM
    Savage's bang on. The best repair would be to take it apart and do it over.
    However, sometimes the best thing isn't the handiest. Click on: PlumbingSupply.com - Leak Repair Kit
    For the second best. Good luck, Tom
    letmetellu's Avatar
    letmetellu Posts: 3,151, Reputation: 317
    Ultra Member
     
    #4

    Apr 22, 2007, 08:40 PM
    Quote Originally Posted by linzyxo
    I just installed a new shower regulator after moving the copper piping. The solder joints are holding but the threads on one side of the regulator are seeping (about 1 drip a min). Looks like the teflon tape missed a thread to two... I can't take it apart and try again because it's affixed to the wall and soldered in tightly to the other two connections. And I can't seal the wall until we fix the drip (and know it's fixed for good).

    I went to home depot and found three products and can't decided on which one to use. Two are epoxies (locktite marine epoxy and NSF Plumbing Epoxy Putty). The other is like super glue but better apparently. Called Amazing Goop for plumbing it claims to be a waterproof contact adhesive and sealant.

    Any experience with any of these or recommendations on what might work? Thanks!!
    I am not sure how you replaced a shower regulator without taking something loose, but that is because I am not sure exactly what you did.

    You say you can't take it apart and try again because of the things you mentioned. If it was installed it can be un-installed and then the joints can be redone with more teflon tape.
    doug238's Avatar
    doug238 Posts: 1,560, Reputation: 62
    Ultra Member
     
    #5

    Apr 22, 2007, 09:01 PM
    [in agreement]
    A rig job is a rig job. A job done right can give a good night's sleep. You may have a bad thread or not tight enough. Do the job right and you will be glad, rig it and you are just waiting till it fails, then the problem is considerably more devastating.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Getting putty off pipe threads [ 2 Answers ]

Hi all. Does anyone know of an easy way to get old plumbers putty off/out of pipe threads? I need to remove the locknut on a bathroom sink drainpipe, and the threads on the pipe are full of old, dry putty |:( Thanks

A/C not cooling, Small Copper pipe COLD and Large Copper pipe room temp. [ 4 Answers ]

I just moved into a newly constructed townhome and the a/c units are of course new. The A/c is not cooling at all. The machine inside turns on as well as the one outside. The inside A/C makes a strange sucking sound kind of like if you were sipping something out of a cup with a straw and you ran...

Broke off copper pipe [ 4 Answers ]

I was trying to replace a bathtub faucet and broke off the copper pipe at the wall is there a way to fix the pipe without calling a plummer or soldering?

Copper pipe in the slab [ 5 Answers ]

In moving our kitchen to another part of the house, I discovered (after removing the old floor cabinets) that the plumbing seems rather "unusual". The 3/4" lines comes out of the floor (slab) to go up to the old sink, but then cross over above the slab about a foot before then going down again...

PVC to Copper Pipe [ 3 Answers ]

I am remodeling a bathroom. The existing drain pipe is 1 1/2" copper tubing. What is the best way to connect a 1 1/2" PVC to 1 1/2" copper tubing?


View more questions Search