|
|
|
|
New Member
|
|
Nov 8, 2007, 08:34 PM
|
|
Plaster walls
Hello what is the best way to cover plaster wall holes about 3" big
|
|
|
Uber Member
|
|
Nov 8, 2007, 08:38 PM
|
|
Can you see wood lath where the plaster was?
|
|
|
New Member
|
|
Nov 9, 2007, 10:50 AM
|
|
Most of the holes are in the ceiling.I rewired my house and I had to do a lot holes to run the wired. The ceiling is halo. Tank you
|
|
|
Junior Member
|
|
Nov 11, 2007, 08:36 AM
|
|
I just went through this. I cut and fit pieces of lathe strip into the holes, then used a quick-setting patching plaster (Web Coat?). First plaster application was a rough fill; after this dried I went back for a final coat. Some sanding may be necessary, depending upon how well you finish the final plaster application with the trowel.
|
|
|
Ultra Member
|
|
Nov 13, 2007, 05:51 AM
|
|
In addition to the above comment, try wetting the old plaster before you apply the new topping, this allows the old to retain a little more moisture during drying time, lessening the cracking.
Ken
|
|
|
New Member
|
|
Nov 18, 2007, 09:48 AM
|
|
Originally Posted by Rover88
I just went through this. I cut and fit pieces of lathe strip into the holes, then used a quick-setting patching plaster (Web Coat?). First plaster application was a rough fill; after this dried I went back for a final coat. Some sanding may be necessary, depending upon how well you finish the final plaster application with the trowel.
What is web coat
|
|
|
Junior Member
|
|
Nov 18, 2007, 10:14 AM
|
|
Web Coat is a fast setting (15-20 minute working time) plaster. I bought it from my local paint store, but I see that Lowe's and Depot sell other brand names of the same type of thing. Mix with water, and it's kind of like drywall joint compound, but sets faster and harder.
|
|
|
Junior Member
|
|
Nov 21, 2007, 10:08 PM
|
|
Sheetrock 20 is another. Be careful when wetting the old plaster. Some the old lime based plasters have a tendency to self-destruct when they get wet.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Stripping paint from plaster walls...
[ 2 Answers ]
I've been able to chip away most of the paint on my 1930's houses' plaster walls down to the plaster. There were two layers of paint and they came off very easily from the wall... almost like an eggshell off an egg. There was a border along the top of the wall, and the paint layers under the...
New wiring in plaster walls
[ 10 Answers ]
Ok, I need any help I can get on this one. I am rewiring my living room of an old victorian house built around 1900. The exterior wall is brick and the interior wall is plaster. The plaster was placed directly on top of the brick (no lath or wood inbetween). Does anyone have any experience with...
Old Plaster walls
[ 5 Answers ]
Ok, just want to check if it is kosher to put a wall frame over top of an old plaster wall, and then drywalling over that. This would negate any removal of the plaster and lath, saving a lot of work! Also leaves it open to move wiring around, which wouldn't be possible if I just drywalled right...
Repairing Plaster walls
[ 1 Answers ]
Our house is over 100 years old. The walls have cracks and places where the plaster is coming loose from the wall. I would like a quick and easy cheap fix. Have any Ideas?
Thank You
Kyle
View more questions
Search
|