Ask Experts Questions for FREE Help !
Ask
    jea2381's Avatar
    jea2381 Posts: 5, Reputation: 1
    New Member
    		  
    #1

    Nov 27, 2012, 10:42 AM
    Trane ycc030f1m0bb that has an LED warning of "flame rollout switch (FL) open"
    I have a Trane ycc030f1m0bb that has an LED warning of 6 flashes, and it means "flame rollout switch (FL) open" I have checked the flame valve that open and closes it (ON/OFF) and I do it either way and after resetting the AC, it turns back on but the 6 flash happens again, the blower kicks on and I guess after is doesn't sense heat it turns back off, I wonder if it's a board issue or a sensor issue or just maybe a cable connection issue, I know there's gas because y gas stove is working and I'm good on that bill, I did just fix a Heat Exchange issue. But not sure why is not working.
    Thank You
    Jaime
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
    		  
    #2

    Nov 27, 2012, 05:49 PM
    What was the heat exchanger issue? A bad heat exchanger will cause the flame rollot switch to trip. The flame rollout switch should be located near the burner area and should have a small button in between two wires that can be pushed to reset. Many times there will be two or three flame rollout switches. However, if you do find the switch and reset it and it trips again, it is time to have a tech in to diagnose the system. A flame rollout switch is a very very important safey device. When it trips you need to take it very seriously and have the system checked. It is there merely to keep you safe and alive, or at least to keep your dwelling from burning to the ground. Please let me know what you find and I will try to help the best I can through this keyboard.
    jea2381's Avatar
    jea2381 Posts: 5, Reputation: 1
    New Member
    		  
    #3

    Nov 28, 2012, 06:41 AM
    Quote Originally Posted by mygirlsdad77 View Post
    What was the heat exchanger issue? A bad heat exchanger will cause the flame rollot switch to trip. The flame rollout switch should be located near the burner area and should have a small button in between two wires that can be pushed to reset. Many times there will be two or three flame rollout switches. However, if you do find the switch and reset it and it trips again, it is time to have a tech in to diagnose the system. A flame rollout switch is a very very important safey device. When it trips you need to take it very seriously and have the system checked. It is there merely to keep you safe and alive, or at least to keep your dwelling from burning to the ground. Please let me know what you find and I will try to help the best I can through this keyboard.
    I looked for any kind of switch or reset button but nothing I even took a video but I'll upload it tonight and post the link and show you what it looks like. I only found the gas on and off near the burners and cables but no buttons.
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
    		  
    #4

    Nov 28, 2012, 06:23 PM
    Looking forward to the video.
    jea2381's Avatar
    jea2381 Posts: 5, Reputation: 1
    New Member
    		  
    #5

    Nov 28, 2012, 07:44 PM
    Got it:
    Trane ycc030f1m0bb that has an LED warning of "flame rollout switch (FL) open - YouTube
    jea2381's Avatar
    jea2381 Posts: 5, Reputation: 1
    New Member
    		  
    #6

    Dec 4, 2012, 10:17 PM
    Helpful!
    jea2381's Avatar
    jea2381 Posts: 5, Reputation: 1
    New Member
    		  
    #7

    Dec 5, 2012, 01:58 AM
    I think I found the answer on this Video ( Flame Roll Out Switch - YouTube ).. Will test today to check.
    mygirlsdad77's Avatar
    mygirlsdad77 Posts: 5,713, Reputation: 339
    Plumbing Expert
    		  
    #8

    Dec 5, 2012, 04:43 PM
    Sorry I haven't been back. Please let me know what you find. I was having a hard time seeing your actuall roll-out switch in the video. Looks like they may be on both sides of the burner assembly. Good luck.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Trane xl1100 diag light indicates flame rollout switch open [ 0 Answers ]

I have an older model trane xl 1100 and last year I replaced a bad board. A few days ago it stopped working. As I checked the board when I turned the thermostat up, the diagnostic light would go from solid green to-blinking 6 times. The attached card shows this to mean "Flame rollout switch (FL)...

Trane XB, 5 led blinks flame rollout open? [ 1 Answers ]

The LED light blinks 5 times says flame sensed when no flame should be present, open rollout switch but this is not the case. I checked the rollout switch and the reset was not tripped and the switch ended up testing to be OK, same with the other 2 limit switches. The old circuit board ended up...

Error code for "open pressure switch" on York natural gas furnace [ 6 Answers ]

I get three red flashes from the furnace after an attempt sequence when the t-stat calls for heat. The motor starts, and seems to try to light but after about thirty seconds, it quits and gives the error code. I have removed both gray tubes from the pressure switch and made sure they are...

Replaced motor now getting "Limit or Flame Roll Out Switch" error [ 11 Answers ]

I replaced the blower motor , and now I'm getting "Limit or Flame Roll Out Switch" error 33. So yes it works, but sometimes it quit with that error and restart immediately. So if it's 66F now and I set it to 70F. It will go all the way to 69F and then quit with that error and start again and so...

Brayant 80t furnace, 'Limit or flame rollout switch is open"? [ 1 Answers ]

HI, I am new here and am having a furnace problem. As a new homeowner I would like to take a look at this myself before just grabbing the phone books. I have a Bryant 80t furnace. Built in 2000 and has been serviced every other year. Unit is clean and in good shape. Woke up to a cold house and...

View more questions Search