Ask Experts Questions for FREE Help !
Ask
    Scrambler81st's Avatar
    Scrambler81st Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Aug 21, 2008, 03:44 PM
    Total Line P374-2800 won't light up
    Help! I am switching from a Honeywell Chron II to a new Total Line P374-2800 and can not get the P374 to light up. Red wire volts read 24vac at wall so am getting proper voltage at stat. HWC II had jumper between R and Rc. Do I need similar jumper on P374? If so, where?
    Have Carrier 2ton a/c split system with 1995 80% Carrier gas furnace

    Here are P374 terms as marked on base plate and schematic.

    (G-fan) (Y1-cool) (W1/O/B-Heat 1st stage) (R-pwr) (C-common) (W1/O/B- Rev. valve) (W2 Heat stage 2) (Misc 1) Misc 2) Misc 3) (RS+5 remote sensor +5vdc) (RS1- remote sensor signal) (RSGND remote sensor ground) (RS2-remote sensor signal 2) (CK1 dry contact switch 1) (CKGRN-dry contact switch 2)
    acetc's Avatar
    acetc Posts: 1,004, Reputation: 79
    Ultra Member
    		  
    #2

    Aug 21, 2008, 06:12 PM
    This thermostat requires a common wire connected to the "C" terminal where as the old one may not have needed a common wire, no jumper on this thermostat, good luck, Mike
    Scrambler81st's Avatar
    Scrambler81st Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Aug 21, 2008, 08:11 PM
    Quote Originally Posted by Scrambler81st
    Help!! I am switching from a Honeywell Chron II to a new Total Line P374-2800 and can not get the P374 to light up. Red wire volts read 24vac at wall so am getting proper voltage at stat. HWC II had jumper between R and Rc. Do I need similar jumper on P374? If so, where?
    Have Carrier 2ton a/c split system with 1995 80% Carrier gas furnace

    Here are P374 terms as marked on base plate and schematic.

    (G-fan) (Y1-cool) (W1/O/B-Heat 1st stage) (R-pwr) (C-common) (W1/O/B- Rev. valve) (W2 Heat stage 2) (Misc 1) Misc 2) Misc 3) (RS+5 remote sensor +5vdc) (RS1- remote sensor signal) (RSGND remote sensor ground) (RS2-remote sensor signal 2) (CK1 dry contact switch 1) (CKGRN-dry contact switch 2)
    Thanks, Mike. For clarification purposes, you are saying that I need to have a wire run from "C" on the air handler (furnace) computer board to "C" terminal on P374?. and DO NOT even attempt to use a jumper on P374?
    acetc's Avatar
    acetc Posts: 1,004, Reputation: 79
    Ultra Member
    		  
    #4

    Aug 22, 2008, 05:51 PM
    Yes that is correct. Mike
    mayorga's Avatar
    mayorga Posts: 1, Reputation: 1
    New Member
    		  
    #5

    Jul 4, 2011, 08:54 AM
    Hi my name is kim,
    My question is if I can install Totaline P/N P274-2800 T-Start to the Tempstar gas package unit?
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Totaline p374-2300 stat [ 4 Answers ]

I have upgraded to the Totaline p374-2300sch stats. I have the install/owners manuals for the two 2200's that I am using, but need to know more about the 2300's that I am using. I know they have "economizer" and pre-occ purge functions as well as "morning warm up", but need to know how to set the...

Total line air condition thermostat [ 3 Answers ]

My thermo set it self at 24. How do I reset to fahrenheit?

Troubleshooting Totaline Thermostat P374-1000 [ 1 Answers ]

I am trying to find out why my Totaline P374-1000 thermostat is blank. Does anyone know if this is just a faulty thermostat or is there an issue with the air conditioner?

Wiring a Totaline P374-200 Thermostat [ 1 Answers ]

I have a Totaline P374-200 Thermostat,I can't seem to make it come on,could you possibily send me a wiring diagram for this thermostat.Thank You Ernie:confused: :confused:

Compaq presario 2800 [ 1 Answers ]

While installing webcam in Win-XP machine, I have an error message "Vedio Capture Hardware not found". Is it Vedio Capture Card essential for Installing Webcam in Win-XP machine?? Plzzzz help me...

View more questions Search