Ask Experts Questions for FREE Help !
Ask
    Robman721's Avatar
    Robman721 Posts: 11, Reputation: 1
    New Member
     
    #1

    Dec 10, 2007, 10:07 PM
    Soon as fan starts up the flame goes out
    When I start my furnace the flame starts and than the fan will come on and the flame will go out and it will continue doing this until I shut it off. And some times the fan will be stuck on until I shut it off directly from the power switch, also there is a blinking red light on the furnace . Any idea what could be causing this?
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #2

    Dec 11, 2007, 04:44 AM
    How many blinks on the lites and brand and model of furnace?
    Robman721's Avatar
    Robman721 Posts: 11, Reputation: 1
    New Member
     
    #3

    Dec 11, 2007, 08:00 AM
    I have an American Standard model #HA03236D175B160573 and the red light is constantly blinking while the heat is on.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #4

    Dec 11, 2007, 09:11 AM
    Continuous blink =
    False Flame or Gas Valve Relay Shorted
    Robman721's Avatar
    Robman721 Posts: 11, Reputation: 1
    New Member
     
    #5

    Dec 11, 2007, 09:18 AM
    OK thanks a lot for the reply
    Robman721's Avatar
    Robman721 Posts: 11, Reputation: 1
    New Member
     
    #6

    Dec 11, 2007, 12:28 PM
    You have any idea on how I could fix that?
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
     
    #7

    Dec 11, 2007, 12:37 PM
    Try cleaning the flame sensor with a bit of steel wool or sand paper.
    Robman721's Avatar
    Robman721 Posts: 11, Reputation: 1
    New Member
     
    #8

    Dec 11, 2007, 12:48 PM
    Thanks a lot ill try it and let you know how it goes.
    Robman721's Avatar
    Robman721 Posts: 11, Reputation: 1
    New Member
     
    #9

    Dec 11, 2007, 01:21 PM
    Well I used sand paper on the sensor and hooked it back up and the red light is still flashing and the heat went on and suddenly went off again. Any other ideas as to why the light would be flashing red and heat still not staying on?

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Flame comes on but goes off [ 2 Answers ]

I have a goodman furance modal gmt115-5b. The flame at heat bar come on only for a few seconds then goes right off.

Inducer motor starts running, but ignition never starts [ 1 Answers ]

I have a Payne Gas forced air furnace, and it's behavior has changed in the last couple of days, where it never gets past the Inducer motor cycle. When we turn on the thermostat (or even jumper across the "R" and "W" leads on the furnace controller) the inducer motor starts running and keeps...

Flame out [ 1 Answers ]

I have a Evcon Natural Gas Furnace. The unit comes on, the combustion chamber fan comes on , the igniter glows orange, the flame ignites and main fan comes on but flame goes out.

No flame [ 1 Answers ]

My pilot won't ignite, and I get 3 flashes from the indicator light, stating either my pressure switch is jammed or vent is blocked, how do I know which is the problem, and is this something I can repair or do I need a specialist? [email protected]

Flame on! [ 4 Answers ]

Please HELP. I'm having a problem with my furnace rather it's my thermostat it's no responding to the temperature. I replcae it with a new one and it's still the same the second I turn power on the flame and fan blower turns on.What could it be. The wring it's only two wires. W and r.


View more questions Search