Ask Experts Questions for FREE Help !
Ask
    rvalli's Avatar
    rvalli Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Dec 15, 2008, 08:18 AM
    Visionpro8000 TH8320U1008 for York heat pump
    Hi
    I have York Stealth electric heat pump. It needs 3heat/2cool settings thermostat. I bought Honeywell Visionpro 8000 TH8320U1008 thermostat. I wired this like below-

    Y2-Brown
    L-Blue
    E-White


    RE, R (jumper together) - Red
    O/B - Orange
    Y-Yellow
    G-green
    C-Black

    I could not find any wire for AUX to connect. System is working fine, but it is too loud in the air handler area. Need help. Did I wired right?

    Thanks in advance.
    hvac1000's Avatar
    hvac1000 Posts: 14,540, Reputation: 435
    Heating & Air Conditioning Expert
    		  
    #2

    Dec 15, 2008, 01:07 PM
    The thermostat will not control how loud the furnace is. It sounds like the fan might be running the wrong speed.
    rvalli's Avatar
    rvalli Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Dec 15, 2008, 02:07 PM
    But it was running fine before I installed this thermostat. Some kind of little bit loud fan noice coming from the handler.

    Last week my compressor blown out, since the system is only 5 yrs old the part is free but the labor is a bundle to handle.

    Do you think my wiring is right?
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #4

    Dec 15, 2008, 02:56 PM

    The wiring of the tstat can't affect it.

    Put the HP on fan and start listening.

    Don't know the furnace, but could you have bumped a DIP switch or something. Something that could change the fan speed.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

York Heating oil furnace with pump /rth7400 [ 13 Answers ]

hello I'm glad there is a place to ask question and getting good answers I installed a rth7400 honeywell thermostat on my york furnace honeywell burner and I can't get heat out of it W \ white wire B \ clear wire Y \ yellow wire

Replacing an old Honeywell Thermostat with a Hunter Model 44260 to a York Heat Pump [ 0 Answers ]

I have an older Honeywell thermostat with wiring G(green) W(white) R(red) X(blue) B(black) O(orange) & Y(yellow). My new programmable thermostat Hunter 44260 has G R/C R/H Y/O W/B & Y1. Which wires go where on the new 44260 thermostat? The manual is not easy to understand. Thanks! D

York heat pump [ 1 Answers ]

I have a older york heat pump that a technician came out to try to repair. He said the board was bad and tried to wire it so that the out side heat pump would run to keep the House cool. Well I found out what had happened to the board (Relay was pulled away from the circuit board from the fan wire...

York heat pump changing from 70 to 72 degrees [ 1 Answers ]

I have a york heat pump and a honeywell model 8300 thermostat. I also have a electric furnace as a backup aux heat. I have the thermostat set to go to 70 at 11:30 pm then at 9:30 am to go to 72. Then heat will operate in this mater. 1 At 9:30 heat pump will start 2 About 1 min later the aux...

View more questions Search