Ask Experts Questions for FREE Help !
Ask
    kwhite3265's Avatar
    kwhite3265 Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Jul 21, 2011, 12:38 PM
    Luxaire heat pump
    Luxaire model eabd f030sb heat pumpfan won't run
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #2

    Jul 21, 2011, 12:47 PM
    Guessing that the compressor is running tells me you have power to unit, so its either the capicitor or the motor itself is bad
    kwhite3265's Avatar
    kwhite3265 Posts: 4, Reputation: 1
    New Member
    		  
    #3

    Jul 21, 2011, 12:59 PM
    I can push the relay in and the fan will run the pipes get hot and should be cold when it runs do I have the wiring backwards
    kwhite3265's Avatar
    kwhite3265 Posts: 4, Reputation: 1
    New Member
    		  
    #4

    Jul 21, 2011, 01:00 PM
    Comment on wmproop's post
    I can push the relay in and the fan will run the pipes get hot and should be cold when it runs do I have the wiring backwards
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #5

    Jul 21, 2011, 01:54 PM
    Comment on kwhite3265's post
    Sounds like u don`t have low voltage (24 V ) to activate the contactor. Do you have a multi-meter? Is the blower on furnace/airhandler running? Set tstat to fan/fan only, not on auto.. if fan runs next you need to check/follow the small tstat mire that runs from furnace to outside condenser for any breaks cuts that might be stopping 24v from going to condenser
    , let us know something
    kwhite3265's Avatar
    kwhite3265 Posts: 4, Reputation: 1
    New Member
    		  
    #6

    Jul 21, 2011, 02:26 PM
    Comment on kwhite3265's post
    The air handle fan runs I do get 24v out side on my red wire if I push the relay over ride switch the fan comes on. Do you know where I can get a manual on the unit luxaire eabd f030sb heat pump
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Luxaire heat pump nz [ 3 Answers ]

Hi I have luxaire heat pump Since yesterday it displaying E2 in place of temp. Can someone guide me the problem in wiring /anything else. Thanks

How do you change a high pressure safety switch on a luxaire heat pump [ 1 Answers ]

High pressure safety switch has yellow wires and apprears to be soldered on. Is that possible or does it come off without removing charge.

What do I hook Y2 out, W2 out, W1 out, X/L, Bsg, Bs on a Luxaire Heat pump board to? [ 3 Answers ]

Luxaire M# HL3A030F1 what do I hook Y2 out, W2 out, W1 out, X/L, Bsg and Bs coming out of board to. What purpose do they serve?

Luxaire heat pump [ 2 Answers ]

I keep replacing 3 amp fuses on furnace and they keep blowing.Why

Luxaire heat pump [ 1 Answers ]

Older model luxaire heatpump will blow warm air in heat mode for several minutes then star blowing out cold air. Unit has new filter and coils are clean. The blower motor. Condensing motor and compressor run but blows cold air. Any suggestions on what problem could be?

View more questions Search