Ask Experts Questions for FREE Help !
Ask
    jmiglino's Avatar
    jmiglino Posts: 11, Reputation: 1
    New Member
    		  
    #1

    Jun 19, 2008, 05:19 AM
    Leg from each transformers and connect the two together can this be used as the commo
    I have two Honeywell Round Thermostats, one for AC one for Heat (gas) both three wire. If I take leg from each transformers and connect the two together can this be used as the common, and wired to my LUXPRO 711 in a 5-wire configuration?
    rsain2004's Avatar
    rsain2004 Posts: 207, Reputation: 6
    Full Member
    		  
    #2

    Jun 19, 2008, 05:26 AM
    Be sure both XFMRS come off the same phase at the distribution panel. XFMRS change the phase 180 degrees they are stepping up or down, from primary to secondary. You wouldn't want two different phase angles... fire hazard...
    jmiglino's Avatar
    jmiglino Posts: 11, Reputation: 1
    New Member
    		  
    #3

    Jun 19, 2008, 06:14 AM
    Can I check phase of each using a dual input scope, making certain both outputs wave are in-phase
    jmiglino's Avatar
    jmiglino Posts: 11, Reputation: 1
    New Member
    		  
    #4

    Jun 19, 2008, 06:16 AM
    Does the a "neutral" on the 120 VAC primary side of the x-former translate to the secondary 24 VAC side?
    jmiglino's Avatar
    jmiglino Posts: 11, Reputation: 1
    New Member
    		  
    #5

    Jun 19, 2008, 06:18 AM
    Can I test for neutral w/VOM checking each of the secondary output against ground to see which is Hot?
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #6

    Jun 19, 2008, 10:08 AM
    It really doesn't matter to check phase in your applicatio.

    But for interest, if the transformers have the same voltage connect the secondaries in parallel. You'll end up with 24 V or 0V. If it's 24V, the phase is identical.
    jmiglino's Avatar
    jmiglino Posts: 11, Reputation: 1
    New Member
    		  
    #7

    Jun 19, 2008, 11:53 AM
    That is so simple, that's right it the two are pi radians or 180 degrees out of phase they will cancel each other out. Your pretty smart. Thanks.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #8

    Jun 19, 2008, 12:28 PM
    You can also use the series test and it's valid for different voltages. Again voltages will add or subtract. So you would end up with 0 or 48 V.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Furnace Transformers [ 1 Answers ]

Train furnace blows 24 volt transformers new original and a new replacement what could cause this and what to check for next

Step down transformers [ 7 Answers ]

How many amps, at 400 volts, can I get from a 300 kva transformer?

Transformers/inverters? [ 2 Answers ]

I need to replace some transformers to gadgets: a) How do I find out which one to buy? b) Where do I get them cheaply? c) Is a generic (by spec only) as safe as the original? Thanks

Help with transformers PLEASE! [ 1 Answers ]

I have to make a simple transformer, that measures the output voltage from the secondary coil, with relation to the distance between the primary and the secondary coil. So, I don't have to make it a step up or step down transformer, I just have to see how the voltage changes with distance. So do...

View more questions Search