Ask Experts Questions for FREE Help !
Ask
    reneeboyd's Avatar
    reneeboyd Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Mar 13, 2009, 11:39 AM
    Do I need a new thermostat?
    My thermostat currently says "in recovery", it is honeywell, not sure of the model as I am not home, for the past couple days the temperature in the house is 10 degrees lower than what the thermostat says it should be at. The unit for the most part will not stay on, when I turn the thermostat on and off the unit will come on for a minute, then shut back off. Do I need a new thermostat? The thermostate is only about a year old
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #2

    Mar 13, 2009, 01:10 PM
    Probably not
    Would help to know the model number
    reneeboyd's Avatar
    reneeboyd Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Mar 13, 2009, 03:06 PM
    The honeywell model is TH4110D, I don't know what model the unit is, I can't find it anywhere. All I see is Kenmore so I took a picture:
    Attached Images
     
    KC13's Avatar
    KC13 Posts: 2,556, Reputation: 99
    Ultra Member
    		  
    #4

    Mar 14, 2009, 09:48 AM
    In the pic, the small round window below the Kenmore logo is a viewer for the status LED. Observe this for a pattern of blinks while the furnace is running and locate the service label that describes the faults.
    Mikie D's Avatar
    Mikie D Posts: 45, Reputation: 1
    Junior Member
    		  
    #5

    Mar 14, 2009, 03:59 PM

    There is a way of resetting the tsat but its in the installation manuel you need the model ## of tstat. Mikie D.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Changed over from White Rodgers Thermostat to Honeywell thermostat [ 3 Answers ]

I have a White Rodgers 2 stage heat/1 cool model 1F58-58 heat pump thermostat that I have changed over to a Honeywell programmable thermostat model RTH7400. Did all the correct wiring as stated in the books but when set to cool, the heater kicks on instead of the central air conditioning. What...

Replacement of Carrier Heat Pump Thermostat with Honeywell TH6000 series thermostat. [ 4 Answers ]

I have a Carrier Series 50QT Electric heat pump that still uses the original non programmable thermostat. I am trying to replace it with Honeywell TH6000 series programmable thermostat. The wiring on the existing Thermostat as follows: O - White, I am thinking this is the Reversing Valve? Y...

How do I wire my new honeywell thermostat replacing the old tempstar thermostat? [ 1 Answers ]

I am replacing my old thermostat. The old is a TEMPSTAR, the new is a Honeywell model # RTH7500. When I use the directions I end up with one left over wire. We called the Honeywell hotline, the rep. said to wire it like this: red to R, white to O, Yellow to Y, Blue to C, Green to G, Orange...

Thermostat turns on furnace and then thermostat shuts back to HOLD [ 7 Answers ]

I believe that when we re-run the program with the correct date and time, if the temp has to go up, the furnace runs until it gets the appropriate temp, then it turns off and when it does that, the thermostat also turns off going to the HOLD state.:confused:

View more questions Search