Ask Experts Questions for FREE Help !
Ask
    Jim McCool's Avatar
    Jim McCool Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Jun 28, 2009, 02:49 PM
    Intermatic T103 Pool Timer
    I have an Intermat T103 pool timer that was installed not long ago but the clock has never run. I'm sure the problem is that it is not wired properly because the two wires for the clock have no voltage across them. I need to know how to properly wire it.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #2

    Jun 28, 2009, 02:56 PM

    http://www.intermatic.com/~/media/fi...20english.ashx
    You should have voltage on the 2 clock wires.
    Check for voltage on all wires, or breaker off/tripped.
    Line in is 1 and 3, line out is 2 and 4.
    Jim McCool's Avatar
    Jim McCool Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Jun 28, 2009, 03:03 PM
    Quote Originally Posted by Stratmando View Post
    http://www.intermatic.com/~/media/fi...20english.ashx
    You should have voltage on the 2 clock wires.
    Check for voltage on all wires, or breaker off/tripped.
    Line in is 1 and 3, line out is 2 and 4.
    I have voltage incoming. In fact, I can turn it on manually and it works. It just won't work on automatic because the close doesn't run.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
    		  
    #4

    Jun 28, 2009, 06:33 PM

    If the clock motor is defective, they can be replaced, Be sure to get number off motor as they have different styles and 120 or 240 volts.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Intermatic t103 timer hook up [ 1 Answers ]

Hi I just installed a Intermatic T103 timer to my water heater. It doesn't seem to be working. I hooked it up two different ways and still the timer stays still. I first hooked it up as the spec. lines 1 and 3 were my line and lines 2 and 4 were my load nothing. Than I tried because it is a 220v...

Intermatic T101 timer will not turn on [ 3 Answers ]

I have a Intermatic T101 timer which is only used once a day (evening). It is turned on at 7:00PM and turned off at 10:30PM automatically. The problem is it has stopped turning on by the tripper. I replaced the on tripper but it still does not work. I can turn it on manually. It does turn off...

Intermatic P1353 3-Circuit Timer [ 7 Answers ]

I am replacing my old Intermatic mechanical time clocks with the digital P1352 Timer. It has three separate circuits. It is a 120/240volt unit. The old timers had Line 1, Line 2 and load 1 and Load 2 blocks. The new timer has three separate Line 1 and Load 1 bolcks - NO Line 2 or Load 2 blocks....

How to select an Intermatic Pool Pump Timer? [ 1 Answers ]

I haven't been able to source a distributor or retailer of Intermatic Pool Timer products in Ontario, Canada. I am looking to purchase one over the internet and have it shipped to me and installed by a local qualified electrician, but I don't know which model to purchase. Intermatic has 4...

Freeze Detector for Intermatic Pool Timer [ 1 Answers ]

Can anyone tell me how to wire a freeze detector into a intermatice dual timer control system?

View more questions Search