Ask Experts Questions for FREE Help !
Ask
    loupi01's Avatar
    loupi01 Posts: 92, Reputation: 1
    Junior Member
     
    #1

    Nov 12, 2008, 10:50 AM
    Monitoring main and/or sub panel
    Is there and inexpensive device to monitor electrical usage (KWH) at the main panel or sub panel? Also is there a device to monitor eletrical usage at a circuit breaker (single circuit)?

    Thank you...
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
     
    #2

    Nov 12, 2008, 04:47 PM
    Others here have found this plug in device:

    P4460 - Kill A Watt EZ kWh Energy Monitor - Home and Office Power Consumption and Usage Monitoring

    Beyond that all I know is the permanently installed electronic submetering units, such as:

    E-Mon Home Page

    A standard unit is about $400.00

    Or there are test instruments that can do it well, such as this $15,000.00 we do recordings for $1200.00 per week:

    http://us.fluke.com/usen/products/PM...keUnitedStates

    Of course it does a lot more than KWH

    And lesser expensive units:

    Power Cost Monitors - PowerCostMonitor.com


    Why may I ask? What are you up to, Lou?
    loupi01's Avatar
    loupi01 Posts: 92, Reputation: 1
    Junior Member
     
    #3

    Nov 13, 2008, 01:59 AM
    Home owner thinks his eletrical bill is high. He lives in a rual area. Has his own well and water tank and at least 4 additional refrigerators and freezers. He wanted to monitor the power from a couple of sub panals to see if it was the power for the house or the power for all outside equipment that was consuming much of the power. Today the local utility company came out to check his power. Found the connections from the transfomer were corroded especially the neutral connection. The home owner also were having a lot of lights bulbs burning out in the recess lights. Could this be attributed to the bad neutral connection?
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
     
    #4

    Nov 13, 2008, 06:08 AM
    The bad neutral connection is exactly the problem causing the lights to burn out. There may be damage done to other devices, such as the refrierators, and their lives may have been shortened if no damage is apparent now.

    Seems the Power Cost Monitor kits will work best to determine the amount of power used in different panels.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Difference between Main Lug and Main Breaker Panel [ 8 Answers ]

What is the difference between a Main Breaker Panel and a Main Lug Panel and can either be used in new residential construction.

Adding sub-panel to Main Panel [ 3 Answers ]

I am currently considering adding an ELECTRIC TANKLESS WATER HEATER. I have a 200 amp (ITE Load Panel G4040ML1200) with 37 of the 40 poles in use. The tankless water heater requires 4- 30amp breakers. My question is... how can I connect a 125 amp sub-panel to the main panel? Your comments are...

Secondary panel from main panel electric [ 2 Answers ]

Can I use a number @2 aluminum ser 4 wires for a 100 amp sub panel?

Breaker size in main panel to support sub panel? [ 7 Answers ]

Hello, I am wiring a sub-panel to the outside of my home (50 feet from main 200 amp box). I ran 3 wire - 6 gauge. What is the largest 2 pole breaker I can put in the main panel to supply the sub-panel. TYPE NM-B 6-3 WITH GROUND 600 VOLTS CIRTEX-I EZ-STRIP (R) PLUS 17:11 2/5/07 SB/RC ...

Main Circuit Panel to Branch Panel? [ 1 Answers ]

Hello experts, OK... My Main Load center in my home has a branch circuit connected to a 60 amp breaker. The branch feed wire is a 4awg copper wire. The branch panel is downstairs and it has a 100amp main cutoff breaker installed in it. It feeds the whole downstairs including... (1)...


View more questions Search