Ask Experts Questions for FREE Help !
Ask
    fsaliani's Avatar
    fsaliani Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Nov 3, 2009, 02:22 PM
    Implications of using a 240 line for a 208 kiln
    I have a 56 amp, 208 volt ceramic kiln that I need to hook up to residential service. It's basically an overgrown toaster oven. Is this even possible and if so what effect will it have on the equipment?
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #2

    Nov 3, 2009, 02:35 PM

    In what country was the kiln made and where will you be hooking it up?
    fsaliani's Avatar
    fsaliani Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Nov 3, 2009, 02:41 PM
    I am in NYC and the kiln is american made too.
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #4

    Nov 3, 2009, 03:22 PM
    Most kiln heating elements are rated to handle 208, 230, 240, and some even up to 277 volts, will operate fine on either voltage.

    Need to check the nameplate rating.

    If the 208 volt element is only rated 208 volts, the element will operate at a higher temp, but, will burn out the element quicker. If there is any damage done, you will be responsible.


    Best to check with the manufacturer's website.
    ohb0b's Avatar
    ohb0b Posts: 215, Reputation: 14
    Full Member
    		  
    #5

    Nov 3, 2009, 03:24 PM
    Without consulting the manufacturer, I'd guess it is resistance heat.
    It will draw more current, heat up faster, and the thermostat will turn it off sooner.
    TKRussel is also correct, the element may burn out sooner.
    fsaliani's Avatar
    fsaliani Posts: 3, Reputation: 1
    New Member
    		  
    #6

    Nov 3, 2009, 04:59 PM
    Thanks for the imput. Turns out all of NYC residential is at 208. FYI they make kilns up to 480 volts for industrial applications.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
    		  
    #7

    Nov 3, 2009, 08:25 PM

    So you are plugging a 208 volt kiln into a singe phase 208 receptacle, so no issue after all.
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #8

    Nov 6, 2009, 04:00 AM
    Funny how some posts take a turn.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

H4 ->H1(1 month)->H4 Tax implications [ 1 Answers ]

Hi, I am on H1B working for whole of last year. My wife had come with me on a H4 visa at the last of previous year(Dec 15 2007 to be exact). This year she got her H1 approved(with change of status) and she was in US till Nov1. She returned again on 25th Dec but using her H4 visa instead of H1....

E-3 Visa - Tax implications for NYC [ 1 Answers ]

Hello, I am moving from Australia to New York in a few weeks and will be working in NYC on the E-3 Visa. I have used PaycheckCity.com | Paycheck Calculator to calculate estimated tax on $75k below: Bi-weekly Gross Pay - $2,884.62 Federal Withholding - $560.54

What are the implications for America? [ 21 Answers ]

Fidel Castro is stepping down, and it looks like his brother's going to take over. Here's the story I saw: Castro resigns as Cuba's leader - Focus on Cuba - MSNBC.com So what might this mean for America in the short and long term? Do you think that free travel will be a possibility? Most...

Kiln Upgrade [ 4 Answers ]

I currently have a kiln that is listed as 30 Amp on the kiln info plate. My new kiln is listed as 44.2 amps on the info plate. The Wire is 8 AWG and the Kiln is less than 10 feet from my 200 AMP service panel. I know that I need to change the Receptacle. I currently have a 14-50P and the new kiln...

View more questions Search