Ask Experts Questions for FREE Help !
Ask
    randamadee's Avatar
    randamadee Posts: 3, Reputation: 1
    New Member
     
    #1

    Jul 17, 2012, 12:41 PM
    Electrical questions
    Hi, I have a power drop to a power shed on a rural piece of land, 200 amps, and want to split from there taking one power cable to a cabin and another to a shop. It is 90 feet to the cabin and 230 feet to the shop. I am either going to do 100 amps to each, or 60 amps to the cabin and the rest to the shop. I want to use aluminum tek for sure. Wondering what size of cable I would need for these scenarios so that I can compare costs before ordering.
    Thanks.
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
     
    #2

    Jul 17, 2012, 01:59 PM
    Run your numbers through this on line voltage drop calculator.

    Voltage Drop Calculator
    randamadee's Avatar
    randamadee Posts: 3, Reputation: 1
    New Member
     
    #3

    Jul 17, 2012, 08:11 PM
    Thanks for the link. Just wondering from that folks, that if 3% is the typical drop in voltage what is the allowable one does not want to work past.
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
     
    #4

    Jul 18, 2012, 05:19 AM
    Maximum voltage drop is recommended to be a total of 5%.

    By the way, I am referring to the National Electric Code and IEEE standards used in the USA.

    We can use 3% for feeders and 2% for branch circuits served by that feeder, or use 2% for feeder and 3 % for branch circuit.

    Generally 3% for feeder and 2% for branch circuits is used.


    Depending on the type of load, you may allow the vD to be as high as you want. I provided IEEE receommendation.

    Resisitve load may work fine with reduced voltage, inductive loads, such as motors, do not work well with reduced voltage, starting a motor is the issue.

    Does this answer your question?
    randamadee's Avatar
    randamadee Posts: 3, Reputation: 1
    New Member
     
    #5

    Jul 18, 2012, 07:53 AM
    I will definite be able to work with that, yes, thank you.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Electrical questions [ 3 Answers ]

Switch position reverse. I have 120v coming from the breaker to the switch box. The box has the in and out white wire tied together and the in and out ground wire tied together. The black wire in and out goes through a single switch. It works fine, but switch positions are reversed On is off...

Electrical questions [ 2 Answers ]

I have recently replaced a lightpost in my yard which had an outlet in the center of the post. The outlet only worked if the light was on. The light was controlled by a hard wired timer which had a black, white, red and green wire. I assume the red and black juiced the outlet and the light. The...

Electrical questions? [ 2 Answers ]

Installing dimmer switch there is hole in wall but no box, their was a switch their attached to dry wall This is a modular home. Should I add a cut in box then put switch ? And there is three wires no 2 just tie all whites together and all blacks and grounds right?

Electrical questions [ 0 Answers ]

Installed a solar panel last january 3 units in basement that convert the dc current to ac Ever since i have been experiencing power surges Some appliances have burned out Tv's will come on in the middle of the night Baltimore put a monitor in for a week and found no problems The solar...

Various Electrical Questions [ 8 Answers ]

GFCI circuitry. Technical purpose and function. Can someone please explain? Also, what is the proper way for an inspector to test a GFCI receptacle?


View more questions Search