 |
|
|
 |
New Member
|
|
Nov 23, 2007, 01:42 PM
|
|
Dual Switch for fan
I am installing a ceiling fan with a dual switch. I have two hot wires coming from switch for the fan and the light. I also have two white wires in the ceiling that are connected to each other. I connected the hot to the fan and the other hot to the light and the white from the fan to the two whites that are connected in the ceiling. The fan is working but the lights are not. Any Help?
|
|
 |
Full Member
|
|
Nov 23, 2007, 02:20 PM
|
|
If you have a voltage tester, then check to see if the wire connected to the light is 'hot' when the switch in on. If you don't have one, then swap the two hots between fan and light and see if the lights work and then the fan does not.
That should narrow it down to whether it is a problem at the switch, or a problem at the light.
|
|
 |
Uber Member
|
|
Nov 23, 2007, 02:30 PM
|
|
It sounds like it is wired correctly, but that is hard to confirm. How is the switch wired? Try connecting both the fan and light wire to the one hot that worked, to confirm the problem is not with the light itself.
Ceiling fan wiring - Ceiling Fans N More
|
|
 |
New Member
|
|
Nov 23, 2007, 02:42 PM
|
|
 Originally Posted by ktrippeer
I am installing a ceiling fan with a dual switch. I have two hot wires coming from switch for the fan and the light. I also have two white wires in the ceiling that are connected to each other. I connected the hot to the fan and the other hot to the light and the white from the fan to the two whites that are connected in the ceiling. The fan is working but the lights are not. Any Help?
I had taken an old fan down and thought that their was a jumper wire from the 2 connnected neutral wires in the ceiling to somewhere but do not remember where. Does their need to be another connection with the 2 connected neutral wires besides the white wire from the fan?
|
|
 |
Uber Member
|
|
Nov 23, 2007, 02:51 PM
|
|
That would depend on how your house is wired. But theoretically speaking, if the fan is working, then the neutral is wired correctly.
|
|
 |
New Member
|
|
Nov 23, 2007, 03:41 PM
|
|
The wires coming from the fan are hot so the light fixture is getting electricity. Brand new and light bulbs work fine.
|
|
 |
Uber Member
|
|
Nov 24, 2007, 12:10 AM
|
|
You have a volt meter? You measured both ceiling wires and the both measure hot? What did you measure them against?
Did you try my suggestion from a few posts up?
If we're not on the same page, then pictures would help.
|
|
 |
Junior Member
|
|
Nov 24, 2007, 05:37 AM
|
|
Let's get into the switchbox too and see what we're working with. Do we have the power supply cable at the switch box? Or is it at the ceiling box and using switch loops. Or God forbid, are they using the ground as a neutral conductor because the house wasn't originally wired for separate control of the fan and light from switch box. That isn't that uncommon. Many houses are wired for just a ceiling light. The homeowner then wants to have a ceiling fan with separate switches for the light and fan. Instead of running new cable, they just use the bare ground as a neutral. Ugh.
|
|
 |
Uber Member
|
|
Nov 24, 2007, 09:02 AM
|
|
Is the neutral for the light connected to the neutral for the fan inside the unit? Again with a meter check to see if you have conductivity between the fan neutral and the light feed of the fan.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Ceiling Fan Dual Switch - Wires don't match up
[ 2 Answers ]
Hi there!
I just intalled a harbor breeze ceiling fan, and followed the wiring instructions specific to having both the fan and the lights controlled by switches, as opposed to a chain. I then purchased a "Cooper 4 Speed Fan/Light Dual Control" switch and am stuck with two questions that I...
Wiring for DUAL wall switch to control Ceiling Fan and Light Separately
[ 20 Answers ]
Greetings. I recently bought a new ceiling fan and light kit to replace one that had been in my sun porch for over 20 years. A dual wall switch was always used to control the light and fan separately on the older fan. The fan speeds were controlled by pull chain. Before I took the old fan down, I...
Ceiling Fan with a Dual Switch
[ 3 Answers ]
I am trying to put in a ceiling fan that was pre-wired to a dual light switch. When I took down the original light I found that I had lots of wires in the box. I had two white wires together, and two black wires, I also have a single white wire, a single red wire, single black wire, and a...
Dual Dimmer Switch for light and fan
[ 2 Answers ]
I am having trouble also installing a dual dimmer switch for my light and fan. I can only get it to work both at the same time. I have a three wire (plus ground) black, white and red going from the switch box to the fan/light. And I have three wires coming from the fan/light unit and three wires...
Trouble with ceiling fan on a dual fan/light dimmer switch
[ 1 Answers ]
I just installed a new Harbor Breeze ceiling fan and dual fan/light dimmer, also from Harbor Breeze. Unfortunately, now I'm scratching my head... Do I have a bad dimmer switch?
Here's the problem:
1. The light will turn on only when the fan speed on the wall switch is set to high.
2. When...
View more questions
Search
|