Ask Experts Questions for FREE Help !
Ask
    johnbpro's Avatar
    johnbpro Posts: 1, Reputation: 1
    New Member
     
    #1

    Apr 27, 2008, 08:19 AM
    Basement sub panel?
    I have plenty of room in my main breaker box (200A) to run circuits for a partially finished basement but was thinking it would make more sense to run a 230V circuit to a panel on the other end of the basement for ease of wiring. The layout would otherwise require a lot of extra wire and drilling.

    The loads will be a utility room with a side by side fridge and a freezer chest, a bedroom (aka living space) and a game room. Future plans could have another living space or two.

    It is ~50' from the main panel to the utility room location I would put the sub. I am a weekend warrior so I have little more than a rule of thumb knowledge for circuit loading. I was thinking a 60 amp in the main, #8 over to the panel, and an 8 position box.

    Am I in the right pew?

    Also, Can I just run the ground in the romex to the main or do I have to strap on to the copper water lines for ground?
    EPMiller's Avatar
    EPMiller Posts: 624, Reputation: 37
    Senior Member
     
    #2

    Apr 27, 2008, 07:42 PM
    It depends on whether you have a good place to put the sub panel. There has to be a certain amount of free space in front of it. Not hidden in the cabinetry. You will need a four conductor supply cable to the sub panel. It will have to be heavier than #8 for 60 amp. Your fourth conductor is all the grounding conductor needed in this case.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #3

    Apr 27, 2008, 08:42 PM
    Neutral must be isolated in the sub panel. The sub-panel MAY contain a main breaker which can be used as a disconnect. The main breaker in the sub, if used, can be rated higher than the feed.

    You may have to purchase a ground bar kit for the sub panel.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

100 amp panel to new 200 amp panel and sub panel [ 3 Answers ]

I have a very small (1000sq feet) 1920 home in Northern New Jersey which 15 years ago was upgraded to breakers with a 100 amp panel. The whole house does have copper romex in it now, and I am adding a substantial addition (3000 sq feet) to the house and I want to put a sub panel in the new portion....

Breaker size in main panel to support sub panel? [ 7 Answers ]

Hello, I am wiring a sub-panel to the outside of my home (50 feet from main 200 amp box). I ran 3 wire - 6 gauge. What is the largest 2 pole breaker I can put in the main panel to supply the sub-panel. TYPE NM-B 6-3 WITH GROUND 600 VOLTS CIRTEX-I EZ-STRIP (R) PLUS 17:11 2/5/07 SB/RC ...

200 AMP Service panel to 200Amp Sub Panel [ 1 Answers ]

I getting new 200Amp service to surface mount service panel. I want to run 2oo cable to bring it sub panel in my Garage which is approx 120Ft Run through ceiling. 2 Questions 1. Is there any ristriction on running a 200AMP inside house to garage ? 2. I got a dirt cheap subpanel that has...

Main Circuit Panel to Branch Panel? [ 1 Answers ]

Hello experts, OK... My Main Load center in my home has a branch circuit connected to a 60 amp breaker. The branch feed wire is a 4awg copper wire. The branch panel is downstairs and it has a 100amp main cutoff breaker installed in it. It feeds the whole downstairs including... (1)...

Kenmore Elite Dryer Toe panel - how to get panel OFF! [ 3 Answers ]

I have a Kenmore Elite Model # 110.600094990 27 inch Electric Dryer - NOW How the heck does one take the Toe Panel Off / or Open this lower section of the dryer? There are two lower edge clips and two upper edge retainers. I CAN NOT get the panel to budge! This is a 7 yr old unit. Thx DAS


View more questions Search