Ask Experts Questions for FREE Help !
Ask
    bradlee's Avatar
    bradlee Posts: 3, Reputation: 1
    New Member
    		  
    #1

    Aug 3, 2006, 05:55 AM
    Balast lights some bulbs, not others
    At work I have a large sign at the front of the building which contains a large ballast and 6, 6' fluorescent bulbs. Everything was working fine last week, but this week only two of the 6 bulbs light up, even after replacing every bulb. Does anyone have any clue what could be happening?
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #2

    Aug 3, 2006, 06:12 AM
    The ballast is most likely defective, however, any one or more of the lamp sockets may be defective also.

    Signs are subjected to all the weather, so water can get in and short out the sockets and wiring, which can cause the ballast to fail.

    Be sure to check each socket and the entire wiring harness to all the sockets for any evidence of arcing or burning.

    Very possible that any one or more of the lamps are also defective if the ballast or sockets failed.
    bradlee's Avatar
    bradlee Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Aug 3, 2006, 08:21 AM
    I should also mention that every socket (including those where the bulbs are not lit) is receiving power, which makes the situation even more strange. I guess this leaves me wondering: is there any reason that voltage would be getting through to the sockets, but resistance (due to water damage in ballast?) prevent sufficient current from being drawn by those affected bulbs?
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #4

    Aug 3, 2006, 09:10 AM
    The power you notice at the sockets is from the output of the ballast, and is irrelevant. As I said, check for any burnt sockets or wiring, and if all OK then replace the ballast.
    bradlee's Avatar
    bradlee Posts: 3, Reputation: 1
    New Member
    		  
    #5

    Aug 3, 2006, 10:04 AM
    Thanks, tkrussell.

    -Brad
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Balast [ 1 Answers ]

I purchased a replacement balast for a circular, double bulb (12 inch and 16 inch, 32 watt and 40 watt) fixture. The old one is a 120 V, 60 HZ, 0.6 A. The new one is a 120V, 60 HZ, 1.1A (outdoor). Is the new one compatible?

Bulbs Burning out TOO fast! [ 1 Answers ]

The light bulbs in my bathroom fixtures are burning out at an alarming rate (1 or to a wek). What might be causing this?

3 lights ran between 2 3-ways, can one of these lights be controlled by a 3rd switch? [ 2 Answers ]

There are 3 lights connected, 2 in one room and the third at the bottom of the stairs. There is a 3-way at the top of the stairs and another in the room with the 2 lights. This guy would like to also be able to switch off just the 3rd light at the bottom of the stairs. I did not dig into this too...

Fixtures burning out bulbs [ 2 Answers ]

Not sure if this is a fixture problem, or some other. It seems that I go through lightbulbs rather quickly in two different fixtures in my house. I've even tried those long life, power-saver bulbs, to no avail. Both fixtures are cheap. One is a basic lightbulb fixture that you plug into a...

View more questions Search