Ask Experts Questions for FREE Help !
Ask
    smorris's Avatar
    smorris Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Sep 18, 2009, 12:57 PM
    12 and 14 gauge ground wires
    My house is 45 years old and has 12 gauge wiring with a 12 gauge ground wrapped in fabric. I have torn down some walls and want to relocate outlets in neighboring walls. Is it OK to use romex wiring that is 12 gauge but has a smaller ground wire? Can I connect these ground wires together, the 12 gauge and the smaller romex, in the line between outlets? So basically it is 12 gauge coming from the ceiling to an outlet, then romex connected and going out to another outlet, and so on to the end of the circuit. Do the ground wires have to be the same gauge or can they be different?
    hkstroud's Avatar
    hkstroud Posts: 11,929, Reputation: 899
    Home Improvement & Construction Expert
    		  
    #2

    Sep 18, 2009, 04:56 PM

    What brand of wire do you have? All of my Romex has a ground wire the same size as the conductors.
    medic-dan's Avatar
    medic-dan Posts: 321, Reputation: 23
    Full Member
    		  
    #3

    Sep 18, 2009, 06:01 PM

    Just an FYI,

    My parents house has romex with the ground wire smaller than the others. It was built in 1969.

    It is out there but not on anything I've seen since.
    smorris's Avatar
    smorris Posts: 2, Reputation: 1
    New Member
    		  
    #4

    Sep 18, 2009, 08:20 PM
    Sorry, the romex is all the same size. The wiring in the house is 12 gauge with a smaller copper ground. The question is it safe to twist these different size grounds together in an outlet? The conducting wires are same gauge, but not the grounds. Is this code?
    tkrussell's Avatar
    tkrussell Posts: 9,659, Reputation: 725
    Uber Member
    		  
    #5

    Sep 19, 2009, 04:32 AM
    The first Romex made had a smaller equipment grounding conductor, and will work just fine.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Joining 2 different gauge wires [ 3 Answers ]

I knocked down part of a wall and as a result need to move some outlet wires. I found a good and legal place to put a junction box but the existing wires are stamped 16amp (35yr old house),(I assume that means about a 14ga) and I have 20ga (romex 12/2)---the circuit has a 20amp breaker. Can I join...

Ground Wires [ 28 Answers ]

OK... Im wiring up a detached building and I have ran into a small problem. Might be a dumb question but here goes. Im feeding from the box under my meter out to the shed. Im running 6/3 w gnd. I got the shed sub panel under control. But in the box under my meter for the fround wire, there is not...

Ground and neutral Wires [ 9 Answers ]

Is it proper to connect the ground and neutral to the neutral buss? I am installing a sub panel from a 200amp svc to a 125 service using 6g. My sub box does not have a separate ground buss rather only 2 neutral buses with a crossbar. I was informed that I can put the neutral and ground on that...

Connecting 14 gauge wire and 12 gauge wires in the same blue box. [ 2 Answers ]

I am wiring my basement. All the outlets are running off 2 independent 20 amp circuit breakers connected to each other by 12/2 wire. I wanted to run some stubs off my 12/2 outlets. All each stub would do is run to a small light (max 180 watts) and of course a light switch. Since I ran out...

Wiring different gauge wires (18 awg to 14 awg) [ 5 Answers ]

I recently bought a house that has a nice wall lamp in the living room that I would like to keep as I renovate it. The lamp came wired with 18 awg wire (1 neutral, 1 hot, and 1 ground). The previous owner wired the lamp to a standard wire with a plug to make it a plug-in fixture. I don't know if...

View more questions Search