Ask Experts Questions for FREE Help !
Ask
    Larry 2704's Avatar
    Larry 2704 Posts: 1, Reputation: 1
    New Member
     
    #1

    May 2, 2013, 08:39 PM
    Whirlpool Model MH1150XM removal
    My old Microwave died. How would one remove this. It is Mounted above the stove. I noticed a casing arrould the Parameter; If I removed this casing. Would there be access to bolts holding the microwave?
    WallyHelps's Avatar
    WallyHelps Posts: 1,018, Reputation: 136
    Ultra Member
     
    #2

    May 3, 2013, 05:02 AM
    Normal installation would be using a mounting plate attached to the wall. This is hung first, then the microwave is hooked onto the plate and then screwed from above to hold it in place.

    Look for a couple of screws coming down from the cabinet above the microwave. Removing these will allow the oven to be tipped forward and out.
    NOTE: IT WILL BE HEAVY. It is best a 2-person job, as it will probably want to come out on its own when you remove the second screw.

    Here's more info: http://www.whirlpool.com/digitalasse...ruction_EN.pdf

    And here's another helpful answer:
    https://www.askmehelpdesk.com/applia...val-57917.html

    Hope this helps,
    WallyH
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #3

    May 3, 2013, 11:23 AM
    If it is not as mentioned above, you may try looking at the 4 corners for screws, on the front, they are not on the surface, you have to look in through venting or slots.
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #4

    May 3, 2013, 11:42 AM
    As noted above, 90% of over the range MW's are hung on a mounting plate behind the unit and then suspended from the cabinet above. Look for 2 screws and washers in the cabinet above the range, near the corners. If you see them, have someone support the MW, unscrew the hanger bolts and tilt out the MW. Install is reverse.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #5

    May 5, 2013, 08:01 AM
    Couldn't find Installation Manual, Here are the parts layout if needed.
    I see a wall template but no upper template which is used for locating the upper cabinet bolts. Since you said "Old", I thought this type may be a possibility.
    Did you find screws/bolts coming down from the upper cabinet?

    http://www.appliancepartspros.com/se...model=mh1150xm
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #6

    May 5, 2013, 08:09 AM
    Just checked the link and noticed "top mounting screws", you should have screws in cabinet.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Whirlpool microwave removal? [ 1 Answers ]

We are trying to remove Whirlpool microwave model MH7140XFZ/year 1999 from the wall brackets. Is it some trick, because we can not get it from those brackets? Can you please help us?

Ignitor removal from a Whirlpool gas dryer [ 2 Answers ]

How do you replace the ignitor on a Wirlpool gas dryer?

Whirlpool microwave removal [ 2 Answers ]

I need to remove an old whirlpool microwave, Model MH6700XM-0, vintage 1986, from under a cabinet over the range. There are no bolts in the bottom of the cabinet. I can see the bottom of the back plate where the bottom of the microwave hooks onto the bottom of the backplate, but there does not...

Whirlpool Model LGQ9030PQ [ 2 Answers ]

Hi everyone. Here's what happened today. My wife went to use our 2 year old dryer, and nothing seemed to work. (it was working fine an hour before) I looked and the washer was not working either. After a quick look, I saw that the breaker had popped. After resetting that, the washer began...


View more questions Search