Ask Experts Questions for FREE Help !
Ask
    nomad-rider's Avatar
    nomad-rider Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Aug 21, 2007, 02:10 PM
    Maytag MDE7600AYW Elec Dryer Timer Does Not Advance
    To whom it may concern,

    I have a Maytag Electric dryer, model #MDE7600AYW with Intelli Dry, My time has stopped advancing in ALL cycles. I have heat in all cycles, however it will run till the cows come home and my clothes are barbie doll size.

    I replaced the timer to no avail (what a waste of $! ) I am beginning to suspect either the dryness sensor of the Intelli Dry control board itself.

    T-stats check out OK. Venting is OK. This dryer has an Intelli Dry dryness control. According to the wiring diagram, power to the timer also flows through the circuit board for the Intelli Dry control.

    If there were a way to place a jumper to isolate the Intelli Dry circuit board, I would be able to determine without a doubt if this was the culprit.

    Please... any assistance will be appreciated.

    Nomad
    amtv serv adv's Avatar
    amtv serv adv Posts: 2, Reputation: 1
    New Member
    		  
    #2

    Aug 21, 2007, 02:52 PM
    Quote Originally Posted by nomad-rider
    To whom it may concern,

    I have a Maytag Electric dryer, model #MDE7600AYW with Intelli Dry, My time has stoped advancing in ALL cycles. I have heat in all cycles, however it will run till the cows come home and my clothes are barbie doll size.

    I replaced the timer to no avail (what a waste of $!!)

    I am beginning to suspect either the dryness sensor of the Intelli Dry control board itself. Please... any assistance will be appreciated.

    Nomad
    It is either a venting problem or a bad tstat(thermosta)
    J Costa's Avatar
    J Costa Posts: 88, Reputation: 9
    Junior Member
    		  
    #3

    Aug 22, 2007, 04:08 PM
    It could be the thermostat that is located on the drum exhaust
    You may also look at the resister it will be located between the heater circuit and timer motor.you can test it for continuity.
    esquire1's Avatar
    esquire1 Posts: 2,483, Reputation: 209
    Ultra Member
    		  
    #4

    Aug 22, 2007, 04:23 PM
    Look carefully at the board for any burnt spots
    Tim Hurd's Avatar
    Tim Hurd Posts: 1, Reputation: 1
    New Member
    		  
    #5

    Oct 6, 2007, 01:13 PM
    Did you find the problem: I have the same symptoms, and have not found the answer: the duct is clear; replaced both thermostats; the dry-sensor; the timer; sworn at it; etc.
    [email protected]
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Maytag Dryer - Timer not advancing in auto dry [ 1 Answers ]

I have a Maytag "export " model dryer, operates on 220V, not two 110V lines. Model MYE3350AGW, Serial 11070998GJ. My wife ran a load in auto dry mode while the exhaust cover outside had been painted shut. Now, the timer does not advance while in auto dry. Timer does advance when in timed dry...

Outlet for elec. Dryer [ 3 Answers ]

I have a wire coming for circuit breaker for an electric dryer. It has 3- wires black, white and open wire. I want to connect them to an outlet. Which one is neutral and which ones are hot? Also if color codes are wrong, is the middle one the neutral and 2 on sides are hot? Thanks

Dishwasher Timer does not advance past final rinse. [ 1 Answers ]

I have a Whirlpool Model #DU920PWKQ0 dishwasher that seems to run fine except when It comes to the final rinse cycle. The timer stops advancing at that point and the dishwasher just keeps on rinsing. The motor was already replaced in it. I figured that it burned out because it never shut off. I...

Whirlpool elec dryer [ 1 Answers ]

After acquiring a Whirlpool Senseon Electric Dryer from a friend I have ran into some issues. It is only 2 years old and the Door Switch Assembly was bad and needed to be replaced. Well, my husband has bypassed that for the time being until we can get a part, but the dryer will shut off after...

View more questions Search