Ask Experts Questions for FREE Help !
Ask
    mpersechino's Avatar
    mpersechino Posts: 1, Reputation: 1
    New Member
     
    #1

    Oct 17, 2012, 05:32 PM
    Maytag dryer only runs with button held down
    My maytag model mdet263ayw only runs when I hold the button down. It has heat . The door switch is working.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #2

    Oct 18, 2012, 10:41 AM
    These driers will do that when the lint builds up like concrete on the inside of the air ducts. The thermal overload has blown open and keeps the dryer from running. You will need a volt/ohm meter to find out which one has blown. These fuses are round with an oval flange that attaches it via screws to the sides of the ducts. They usually have gray wires going to them on Maytag dryers, and when you are tracing the circuits they will wire the fuses in series, so you can follow the wires to find all of the fuses. Also, the sensors get blocked from sensing when the dryer is dirty. Halfway cleaning it will not work because all it takes is one clogged up air passage or dirty sensor. You need to totally tear it down and scrape out and wash all of the parts except the motor, which you vacuum out. You can go to YouTube to see videos on how to take it apart, but do a very good job or it will fail again quickly. I would get a new belt and change it while you have it apart and get some white lithium grease and grease any bearings you find. You need to clean out a drier every two years, at least, according to the manual. You just unplug the wires from the sensors and remove ductwork that they are attached on and clean the entire thing with soap and water. Make sure you go all through the dryer and get all parts like the blower fan and housing (it has to be scrubbed and washed out), vacuum out motor well and clean exhaust. Mark all wires you unplug so you know where they go. If you leave any dirt in the ducts it will blow another fuse quickly or will not maintain the temperature correctly. This is an easier job than you would think. My sister does hers at least once a year since she has five children and the dryer gets a lot of use. Make sure to clean around all of the sensors, and you can check them with a meter and the chart in one of the manuals, too. See: Dryer vent cleaning prevents fires - YouTube and: Cleaning out a dryer with top lint cleanout - YouTube
    Cleaning out a dryer: By a woman 2 of 2 - YouTube
    Here are some Maytag manuals: https://dl.dropbox.com/u/8010163/Maytag%20Dryers.zip
    https://dl.dropbox.com/u/8010163/How...e%20Manual.pdf
    Make sure to get a decent digital meter. You can buy good ones at Radio Shack or Home Depot for about $20-45.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Mod dcvh515ef0ww dryer runs after pressing stop button? [ 0 Answers ]

I have a ge mod dcvh515ef0ww dryer that still runs after stop button is pushed

Kennmore dryer will not stay running unless start button is held [ 5 Answers ]

Sears Kennmore Model 11063952102 (Electric) As stated in the title, the dryer will not stay running unless the start button is physically held down. If it is released, the drying immediately stops. The dryer seems to work fine otherwise, I have not noticed any increased time to dry or other...

Kenmore Gas Dryer no heat.stops until button held [ 1 Answers ]

Hope someone can help:) I have a Kenmore Elite Dryer... model 11072932100 and it stopped working. Every time the start button is released it stops spinning and it doesn't seem to heat up either. I've cleaned lint,etc... Help...

Maytag dryer runs too hot [ 5 Answers ]

Maytag dryer runs too hot. Does not seem to go to cool down cycle even on Perm Press setting. Where can I find an electrical schematic?


View more questions Search