Ask Experts Questions for FREE Help !
Ask
    artistb's Avatar
    artistb Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Apr 15, 2007, 12:48 PM
    He3 Kenmore Elite Dryer Won't run selected cycle.
    I have a HE3 Kenmore Dryer Elite.

    All lights work and you can push selected functions. When you push the start button it sounds like it just clicks off. Won't start the cycle... is this a sensor relay switch problem. The venting and lint is clear.

    Thanks
    artistb's Avatar
    artistb Posts: 2, Reputation: 1
    New Member
    		  
    #2

    Apr 16, 2007, 07:50 PM
    Well I guess I will answer my own problem here.

    After talking to one of my appliance repair friends... I followed up on his instructions.. to find my thermal fuse and thermister. Did a check on my fuse and that was the problem. So I replaced the fuse and thermister control... all is working fine. Cheap repair I must say could have been worse.
    mdsmshea's Avatar
    mdsmshea Posts: 2, Reputation: 1
    New Member
    		  
    #3

    May 16, 2007, 02:20 PM
    Quote Originally Posted by artistb
    Well I guess I will answer my own problem here.

    After talking to one of my appliance repair friends...I followed up on his instructions..to find my thermal fuse and thermister. Did a check on my fuse and that was the problem. So I replaced the fuse and thermister control.....all is working fine. Cheap repair I must say could have been worse.
    My he3 is doing the same thing was it the fuse or the thermister and where are these parts located?

    Thank You,
    Michael
    mdsmshea's Avatar
    mdsmshea Posts: 2, Reputation: 1
    New Member
    		  
    #4

    May 16, 2007, 02:36 PM
    Quote Originally Posted by artistb
    I have a HE3 Kenmore Dryer Elite.

    All lights work and you can push selected functions. When you push the start button it sounds like it just clicks off. Won't start the cycle....is this a sensor relay switch problem. The venting and lint is clear.

    Thanks
    Can you help me find fuse and thermister on my he3 i have the same problem
    Thanks michael
    shutcherson's Avatar
    shutcherson Posts: 1, Reputation: 1
    New Member
    		  
    #5

    May 31, 2007, 02:18 PM
    Quote Originally Posted by artistb
    I have a HE3 Kenmore Dryer Elite.

    All lights work and you can push selected functions. When you push the start button it sounds like it just clicks off. Won't start the cycle....is this a sensor relay switch problem. The venting and lint is clear.

    Thanks
    Shutch
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kenmore Elite HE3 Electric Dryer [ 1 Answers ]

My dryer turn off all by itself. An error code of E1 appears. We press start/cancel and start the dryer again. After a few minutes it shuts off again displaying the error code once again. Help... :eek:

Kenmore Elite HE3 Dryer Not Heating [ 1 Answers ]

I have a Kenmore Elite Dryer (electric) that is not heating. I pulled the toe panel so I could clean it out to see if that was the problem. After I cleaned it out I ran a short cycle and still no heat. I also noticed the heating coil did not change. Should these get hot, turn red during a drying...

Kenmore Elite Dryer Won't Heat on Timed Cycle [ 1 Answers ]

I have a Kenmore Elite Dryer that is 4 years old. The dryer will not heat on the timed cycle, but it will heat on the Even Heat Cycle. The heating element will not com on when I have the timed cycle selected. On the Even Heat Cycle all of the temperature settings work. My dryer has a rotary...

View more questions Search