Ask Experts Questions for FREE Help !
Ask
    colonelron's Avatar
    colonelron Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Feb 18, 2010, 02:39 PM
    Dryer fires on startup but won't refire when ignitor comes on during cycle.
    This is a Whirlpool LGR5620KQ1, and starts up fine... the ignitor glows and the gas valve opens, producing a nice fire. The dryer then reaches temp and shuts off the burner. Later, when the ignitor re-ignites, however, the burner does not actuate. The ignitor remains glowing for maybe 5 to 10 seconds and then simply goes out... no fire. I have been told that this sounds like a gas valve coil problem, but I do not understand how the coils would be defective if they are allowing the primary actuation to occur when the dryer is started for the first time. I should note that, upon allowing the dryer to rest for about 10 minutes, it does properly fire upon restart. I have checked for lint buildup and there was virtually none. The blower is working fine. Nonetheless, I did clean the entire dryer system out with high pressure air and it is now as clean as new, yet with the same result. I'm stumped, and don't want to purchase parts that I don't need. Any help would be greatly appreciated. Thanks.
    parttime's Avatar
    parttime Posts: 1,440, Reputation: 113
    Ultra Member
    		  
    #2

    Feb 18, 2010, 03:15 PM

    Read this The Virtual Repairman's Appliance Help :: View topic - Whirlpool nat. gas dryer won't light 2nd time you can order the parts there also, good luck
    colonelron's Avatar
    colonelron Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Feb 18, 2010, 06:01 PM

    Just a quick thanks for your prompt reply. I ended up replacing both coils and the thing seems to be working like a champ. Thanks again.
    parttime's Avatar
    parttime Posts: 1,440, Reputation: 113
    Ultra Member
    		  
    #4

    Feb 18, 2010, 06:09 PM

    Your more than welcome, thanks for letting us know the outcome.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

I have a gas dryer that quit working... How do I know if it's the ignitor? [ 2 Answers ]

It quit heating up... The drum turns.. No glow on the ignitor...

Maytage Gas Dryer Ignitor [ 1 Answers ]

Maytage Gas Dryer - Model MDG9606BWW - dryer wasn't heating, removed front panel and notice ignitor had a crack - removed and replaced with a new one. After 20 min dryer was not heating, removed panel and saw that the new ignoitor had burnt out. Before buying another ignitor would like to know if...

Maytag dryer ignitor replcmnt. [ 3 Answers ]

This is directed to HVAC1000 located in Ohio could you please send me your email address... this pertains to the maytag gas dryer with a bad ignitor... contact me at [email protected]... thanks

Whirlpool Dryer Ignitor - Replacing [ 3 Answers ]

Trying to replace the ignitor on a Whirlpool clothes dryer. My dad has done this a number of times. This one is a little different. The model # is LGC6848AQ3. He said it appears replacement will be from the front. Back is removed and he's trying to remove the top, so he can get to the screws...

Kenmore Dryer Ignitor [ 1 Answers ]

I recently replaced my kenmore 70 series dryer's ignitor. Before it would glow orange and turn off. Now it glows orange and sparks an open flame. Is this normal? Thank you for your help, Matt

View more questions Search