Ask Experts Questions for FREE Help !
Ask
    A00402213's Avatar
    A00402213 Posts: 2, Reputation: 1
    New Member
     
    #1

    Nov 5, 2011, 10:37 AM
    Belt for Kenmore dryer soft heat heavy duty plus?
    The dryer won't turn
    ma0641's Avatar
    ma0641 Posts: 15,675, Reputation: 1012
    Uber Member
     
    #2

    Nov 5, 2011, 11:06 AM
    Can you hear the motor start? If so, for many Kenmore dryers you will need to remove the top and front of the dryer to install a new belt. You will have to support the drum. Make sure to check the belt tensioner. Unless you have some basic tools and are reasonably good taking things apart, let a service tech do it.
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #3

    Nov 5, 2011, 11:07 PM
    Make sure to clean it well and lubricate it with lithium grease or it will fail very fast. DrTom4444
    Alxfish's Avatar
    Alxfish Posts: 1, Reputation: 1
    New Member
     
    #4

    Apr 16, 2012, 09:52 PM
    How to take off front of Kenmore soft heat heavy duty dryer
    drtom4444's Avatar
    drtom4444 Posts: 3,282, Reputation: 145
    Ultra Member
     
    #5

    Apr 17, 2012, 11:28 PM
    It sounds like you have a broken belt, but if has run long enough to wear out the belt it needs cleaning, too. You need to totally tear it down and scrape out and wash all of the parts except the motor, which you vacuum out. You can go to YouTube to see videos on how to take it apart, but do a very good job or it will fail again quickly. . I would get a new belt and change it while you have it apart and get some white lithium grease and grease any bearings you find. You need to clean out a drier every two years, at least, according to the manuals.
    Look at: How to clean your clothes dryer. How to make it hot again. - YouTube to see how to tear it down. Also: Mr. Appliance Tips: How to Clean Your Dryer - YouTube ; Cleaning a Dryer Vent and Lint Trap - YouTube
    Electric Clothes Dryers
    Whirlpool Dryer Model LE5800XSW3 Wiring Diagram | Dryer Repair | Fixitnow.com Samurai Appliance Repair Man
    The job is very easy for a woman to do. Just get it out into your garage or somewhere you will have plenty of space. Pop the top and unplug the wiring harness, then you can see where the screws are that hold on the front. You will need to unplug the door switch. You should lay it on its back to make it easier to work on before pulling off front. Make sure to clean it very well and don't miss the duct on the door going to filter or the other ducts in the rear, and the blower wheel which is very, very important. A clog of cement-like lint build up can hide anywhere. Don't be afraid to take apart anything to be able to look inside and clean it. One missed place will necessitate doing all this again and no one wants to redo something. Grease all support rollers
    With white lithium grease and reassemble and you have a new dryer.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kenmore Heavy duty soft heat dryer won't turn ? [ 2 Answers ]

Kenmore Heavy duty soft heat dryer won't turn, still heats up, motor still hums, but, won't turn!

My Kenmore Heavy Duty Soft Heat series dryer is rotating off center in the machine. [ 1 Answers ]

I removed the top but could see nothing broken but suppose the culprit must be under the drum that's causing the problem. How do I access the problem? When you look inside you can see that the drum is resting at a slight angle as there's an uneven gap between the front and back rims and the drum....

Heating Problem - Kenmore Heavy Duty 60 Series Soft Heat [ 4 Answers ]

My Kenmore Heavy Duty 60 Series Soft Heat Model 96565210will not heat on any setting. The dryer runs normally, it just won't heat at all. We did install a new heat element, and that would not heat up. Any help is appreciated!

Kenmore soft heat large capacity heavy duty push to start button won't work [ 2 Answers ]

I have a heavy duty kenmore dryer and the push to start button on it will not start the dryer. It feels like it has disconnected somehow but I don't know. I am looking to buy the parts to fix it with. Help please.

Kenmore heavy duty 60 series soft heat large capacity [ 2 Answers ]

Dryer will not heat


View more questions Search