View Full Version : Water heater pilot light problems
ipcfarm
Nov 5, 2006, 12:06 PM
Pilot went out, no problem relighting. BUT when I turn up the thermostat, the flame gets out of control and escapes from the two protective doors. It has started melting the plastic on the outside of the tank around the drain valve.
Morganite
Nov 5, 2006, 12:11 PM
Pilot went out, no problem relighting. BUT when I turn up the thermostat, the flame gets out of control and escapes from the two protective doors. It has started melting the plastic on the outside of the tank around the drain valve.
It seems very much as if a maintenance visit is long overdue. Your burners could be worn, and if so will allow the flames to go where they want rather than where they should. See if friends will recommend a reliable engineer they have used.
When the burners wear out the gas does not burn as it should and the result is often a dangerous increase in carbon monoxide output, and that can be FATAL. It doesn't smell, but it replaces the oxygen in the bloodstream and you die with a ruddy glow on your cheeks. CO1 combines with heamoglobin in your red blood corpuscles twenty-six times more readily than O2 does.
Please treat this as urgent and life threatening.
M:)RGANITE
ipcfarm
Nov 5, 2006, 12:19 PM
Pilot went out, no problem relighting. BUT when I turn up the thermostat, the flame gets out of control and escapes from the two protective doors. It has started melting the plastic on the outside of the tank around the drain valve.
The unit is only 5 years old. How often should maintenance be done and what exactly should be done for maintenance.
labman
Nov 5, 2006, 01:23 PM
Do you have any other gas appliances, and are they working OK? I hardly see it likely for much to go wrong except the outside pressure regulator sticking resulting in excessive pressure. I would almost be afraid to tell you to turn another one on. Perhaps the best thing is to call the gas company. You don't want to pay a contractor $100 to come out and tell you the gas company's regulator is bad.
It sounds to me like it may be out of adjustment. If it had been working right, I don't see the screw turning itself. I am afraid this is a job for a professional.
Ordinarily, hot water heaters go for years and years needing no more than a new thermocouple. If you follow Tom's advice on flushing them, they should go even longer.
labman
Nov 5, 2006, 01:44 PM
Thinking some more about this, it could be a draft problem, especially if you have a forced draft. Check your vent carefully. Do you not hear a small blower which you used to when the gas was on?
ipcfarm
Nov 5, 2006, 02:07 PM
My water heater is next to my furnace. Gas line is split between them. Furnace is running just dandy. The thermocouple seems fine. The flames don't want to stay on the burner. On the outside of the tank there is a lot of melted plastic and black soot/singe marks on the metal from the flames escaping.
speedball1
Nov 5, 2006, 02:22 PM
What color is the flame. Yellow? Yellow/red? Blue? Blue/yellow?
ipcfarm
Nov 5, 2006, 02:23 PM
It's blue. I have seen a little red/orange when it shoots out. But mostly blue.
speedball1
Nov 5, 2006, 02:55 PM
Then the air adjustment's set OK.
Morganite
Nov 6, 2006, 12:36 PM
Do you have any other gas appliances, and are they working OK? I hardly see it likely for much to go wrong except the outside pressure regulator sticking resulting in excessive pressure. I would almost be afraid to tell you to turn another one on. Perhaps the best thing is to call the gas company. You don't want to pay a contractor $100 to come out and tell you the gas company's regulator is bad.
It sounds to me like it may be out of adjustment. If it had been working right, I don't see the screw turning itself. I am afraid this is a job for a professional.
Ordinarily, hot water heaters go for years and years needing no more than a new thermocouple. If you follow Tom's advice on flushing them, they should go even longer.
Labman,
You are both disingenuous and dangeorus. You might have had a heater twenty-five years without any maintenance done on it, but it is recommended by the industry that they are checked annually. Carbon monoxide is a killer. That is not disinformation. I respectfull;y suggest that you forget your own anexcdotal evidence when delaing with matters that could cost lives.
A landlord has recently been charged with murder after the death of his tenants from CO1 poisoining from an unmaintained gas water heater.
Look at this site, rewad the cases, and then you shou8ld a[pologize to me and to th epersaon to whom you gave such atrocious and dangerous advice, and you hsou8ld remove your advice from the public forum and refrain from offering your opinions on matters of such importance as life, disabiluty, and death.
http://www.carbonmonoxidekills.com/carbon_monoxide_inthenews.htm
--------------------
Just a few of the multitudes of cases on the site:
Landlord may face civil charges in death
By Judith Scherr Daily Planet Staff (11-30-00)
The 17-year-old Indian immigrant died Nov. 24, 1999 from carbon monoxide poisoning in an apartment at 2020 Bancroft Way owned by L.B. Reddy Real Estate Company.
“...the causes of her death were exposure to fumes from a dangerous, defective, and negligently-maintained gas heating system at 2020 Bancroft Way and the failure of defendant Lakireddy Bali Reddy to secure prompt medical attention for her after such exposure,” according to the suit.
--------------------
Stacey Rodgers has penned Our Children That Live In Our Heart as she bids to come to terms with the death of 10-year-old Dominic at their West Yorkshire home. Tomorrow is the first anniversary of the tragedy and Stacey has joined forces with British Gas in a bid to make every other parent in the country aware of the potential dangers of CO – known as the silent killer.
\Carbon monoxide clears school
Benton County Daily Record, AR - 21 hours ago
BENTONVILLE — Carbon monoxide exposure forced evacuation of Washington Junior High School on Thursday and sent more than 50 students to the emergency room.. .
100 evaucated in carbon monoxide leak
Allston-Brighton TAB, MA - 14 hours ago
An single alarm saved the lives of more than 100 Allston residents early Thursday morning after it alerted sleeping tenants to a deadly carbon monoxide leak.. .
Carbon monoxide likely cause of couple's death
Seattle Post Intelligencer - Feb 10, 2005
Students taken to hospital after carbon monoxide leak
Boston Globe - Feb 10, 2005
Students Evacuated After Carbon Monoxide Leak Boston Channel.com
Allston tenants saved by CO detector Boston Globe
Sixteen residents of a Holyoke housing complex are lucky to be alive following their escape this week from apartments where deadly carbon monoxide gas had...
Carbon monoxide sends 16 to hospital The Republican
2 remain in hospital in monoxide poisoning The Republican
Carbon monoxide suspected as couple found dead
TheNewsTribune.com, WA - Feb 10, 2005
Two boys found suffering from presumed carbon monoxide poisoning
DetNews.com, MI - Feb 8, 2005
Support builds for mandatory carbon monoxide detectors
Gloucester Daily Times, MA - Feb 8, 2005
The sense of urgency comes after a 7-year-old Plymouth girl died from carbon monoxide poisoning last month when snowdrifts blocked a heating vent.. .
Firefighters look to douse carbon monoxide calls
Green Bay Press Gazette, WI - Feb 10, 2005
UTC Student Dies Of Carbon Monoxide Poisoning
The Chattanoogan, TN - Feb 9, 2005
A UTC student apparently died accidentally of carbon monoxide poisoning while talking on a cell phone while her car was running in her garage.. .
Carbon Monoxide Forces Residents from Apartments
WTOP, D.C. - Feb 8, 2005
Children Overcome by Carbon Monoxide
WXYZ, MI - Feb 9, 2005
Boys Waiting In Car Overcome By Carbon Monoxide
DETROIT Two children are listed in critical condition after suffering what Detroit police say was carbon monoxide poisoning in their garage.. .
16 evacuated in Holyoke carbon monoxide leak
The Republican, MA - Feb 8, 2005
Older Couple Found Dead From Apparent Carbon Monoxide Poisoning
KOMO, WA - Feb 9, 2005
Carbon Monoxide Leak Triggers Evacuation
Boston Channel.com, MA - Feb 9, 2005
Five children die of carbon monoxide poisoning
NORWALK -- Defense attorneys for a Pico Rivera father facing five counts of murder in the carbon monoxide deaths of five of his six children asked for additional time Wednesday in Norwalk Court to prepare more motions.
Husband killed by carbon monoxide
A woman in Lewis County told Hamrick Monday that Saturday's destruction took place just a month after carbon monoxide poisoning killed her husband at their home. Now, she's left literally picking up the pieces of her home.
And so forth ad nauseum!
Please take a long pause before you set about insouciantly dispensing advice on matters of which you not only know too little to be helpful, but in which you are dangerous and potentially fatal. Would you pay $100.00 to endure the safety of your family and pets? Your advice should carry a government health warning. I am more than a little surpised at you because you seem like a nice and intelligent fellow.
Disinformation? Absolutely not!
M:)RGANITE
Morganite
Nov 6, 2006, 12:49 PM
Thinking some more about this, it could be a draft problem, especially if you have a forced draft. Check your vent carefully. Do you not hear a small blower which you used to when the gas was on?
You really ought to refrain from offering advice on important matters of which you have no training and experience. I am sure you mean well, but your advice is downright dangerous.
http://www.carbonmonoxidekills.com/carbon_monoxide_inthenews.htm
Almost 30 deaths occur annually in the British Isles alone from incidents involving carbon monoxide.
Dr Kim Howells, British Consumer Affairs Minister, has launched a new safety awareness campaign to warn of the dangers posed by carbon monoxide in the home.
Less than half of those questioned could list the possible causes of a build up of carbon monoxide or knew the warning signs of carbon monoxide in their homes.
An indoor exhibition unit is to tour the UK warning of the dangers of carbon monoxide; and a new resource pack about the safety of heating systems for use by safety professionals.
Dr Howells was "staggered" by the lack of knowledge among the general population. He said: "The message is simple - if you haven't had your coal fire chimney swept for years, or you've no idea when your gas boiler was last serviced, don't wait until it's too late. Take action now."
Between 1990 and 1999 in the UK, more than 500 people have died of carbon monoxide poisoning as a result of faulty domestic heating systems, including water heaters. What emerges from a study of the casualties is that:
Older people and home-owners are at the highest risk;
Older people are ten times more likely to die than students;
Those using non-gas fuels are also far more likely to fall victim to carbon monoxide poisoning, mainly as people are less aware of the hazard of carbon monoxide with non-gas fuels; and
Non-gas fuels such as coal, oil and paraffin can be just as deadly as gas - they account for 41% of all carbon monoxide deaths.
Further advice and information
British Gas posters and leaflets about the symptoms of carbon monoxide are going to GP surgeries to help alert people.
Free advice on gas safety issues is available from the HSE gas safety advice line on 0800 300 363.
Advice
The Department of Trade and Industry's advice for the public is:
get your appliances checked for safety every year by a competent engineer (make sure he/she is CORGI registered.
If you have a gas appliance
` ensure your home is properly ventilated - never block vents;
` make sure all chimneys and flues are regularly swept and kept clear;
` CO detectors are a valuable warning device, but not a substitute for regular servicing of heating systems; and
` only buy carbon monoxide detectors that comply with BS 7860; and
` if anyone suspects carbon monoxide poisoning, they should: switch off all heating appliances; ventilate the property; and contact the emergency hotline
Failure to recognise the high risk of permanet disability, brain damage, and fatality is the biggest barrier to making homes safe. Any change in the nature or direction of the flames in a gas appliance should be treated with the utmost cautioon and professional help engaged IMMEDIATELY.
M:mad:RGANITE - who has witnessed the effects of CO1 poisoning too often to ever take it lightly, or to take risks with the lives of others, by doling out stupid advice, dammit!
Morganite
Nov 6, 2006, 12:55 PM
Pilot went out, no problem relighting. BUT when I turn up the thermostat, the flame gets out of control and escapes from the two protective doors. It has started melting the plastic on the outside of the tank around the drain valve.
I must reiterate the advice I first gave you. It seems that your burner is malfuncitoning. Please have it checked by a registered and certified gas engineer in the interests of your own safety.
You have been given some poor, even dangerous, advice, but not by me.
Please ensure your family is safe!
M:)
Morganite
Nov 6, 2006, 12:58 PM
It's blue. I have seen a little red/orange when it shoots out. But mostly blue.
Red/orange flame indicates improper combustion. Significant for CO1! You not only have a significant fire risk, but a carmon monoxide gas poisoning risk also. Either could be fatal. Shut it down and get a certified gas engineer to inspect it.
M:)
labman
Nov 6, 2006, 01:10 PM
I invite anybody with any doubt about my advice to see https://www.askmehelpdesk.com/heating-air-conditioning/water-heater-problems-40966.html
You will see Northern Heat, a true professional we are lucky to have here, is giving about the same advice as me.
I also suggest anybody that thinks the problem is worn out burners to post that to that thread too.
Morganite
Nov 6, 2006, 01:13 PM
CENTERS FOR DISEASE CONTROL AND PREVENTION
WINTER HOME HEATING HAZARDS
Thursday, October 26, 2006, 12:00 PM
This afternoon, we'll be coming to you to discuss some of the winter home heating hazards that are experienced by most Americans … a joint presentation by the Centers for Disease Control and Prevention, the Consumer Product Safety Commission and the Air Conditioning Contractors of America, highlighting a silent, insidious killer, and a silent public health issue: carbon monoxide poisoning … change the batteries in their carbon monoxide detectors, an important part of the overall preventative approach to carbon monoxide poisoning … We're all familiar with trip and fall hazards, but not enough of us are familiar with carbon monoxide … carbon monoxide … is a silent and insidious killer. It's colorless. It's odorless. It's poisonous. We lose almost 500 Americans every year to [death from] carbon monoxide inhalation, five times as many as we lose to West Nile virus. Non fatal carbon monoxide poisonings, the ones that don't kill people but make them sick send an estimated 15,200 people to emergency departments every year … exposures to carbon monoxide can cause headaches, dizziness, weakness, vomiting, chest pain, confusion, and in some cases, long lasting neurologic damage … Faulty gas furnaces cause more carbon monoxide poisoning than any other source … whenever you burn fuel, you may be creating carbon monoxide. And … you may be exposed to excessive levels of carbon monoxide. Not only gas furnaces need our attention, but gas burning appliances, gas or wood burning stoves, fireplaces, and generators, when they're used in enclosed or semi enclosed spaces … these are preventable deaths, preventable injuries … and taking simple steps can protect you, your family and your pets from carbon monoxide poisoning.
[G]et your heating ventilating and air conditioning system serviced by a qualified technician. That technician should look not only at the furnace, but at water heaters and any other gas, oil or coal burning appliances every year... appliances that are not working properly are more likely to cause carbon monoxide poisoning … [Glenn Hourahan from ACCA] ACCA is the trade association representing the contractors in the U.S. who install, service, and maintain heating, ventilation and air conditioning equipment. I'm here to support the message coming both out of CDC and CPSC … and to reiterate, the requirements and the necessity to have your home heating systems inspected annually to ensure that they're operating properly. Proper operation will ensure that carbon monoxide is not generating excess levels as well as to ensure that carbon monoxide that is generated within the combustion process is vented. So reiterating the message that has all ready been spoken we strongly encourage that home owners engage the services of qualified contractors to have technicians come to their homes, to have their systems inspected, to make sure they're operating properly, to make sure the venting systems are performing properly. To ensure that other equipment and systems that might be connected to a common vent are working properly. … This might be water heaters.
When having a contractor, a technician come to your home, there are certain things that this technician is doing and there are certain things that consumers should check ensure are being done. One of the most important things that a contractor will do is ensure that the heat exchange does not have any cracks in it. This will prevent carbon monoxide from being directly vented from the combustion process and released into the occupied space.
They are also going to be looking directly at the flue and the venting pipes to ensure that they are sound, no rust, no corrosion, no wholes and no evidence that they might soon be occurring. They will look at the burner assembly as well as the blower assembly to ensure that they are going to be - that the equipment can operate properly and that complete combustion will occur.
There are also a number of measurements and adjustments and cleaning that will be done within the various heating systems and ventilation systems to ensure that they will perform properly. While in the building, a qualified contractor will also look beyond just the equipment itself.
They'll be looking for situations that could cause a very dangerous build up of carbon monoxide in a home … what's called flame rollouts, so the flame on your burner can roll out and cause incomplete combustion.
You can also have backdrafting, either down a chimney as well as down the vent flue from the combustion equipment itself, as a result of pressurization problems. So the contractor will be looking for these situations … it should be recognized that doing this on an annual basis is a good idea, because not only does it reduce carbon monoxide possibility of entering the home, at the same time, it leads to better equipment performance, and reduced fuel use, which is always good as well.
Yes, we strongly encourage that consumers and homeowners look for NATE, North American Technician Excellence, look for those who are certified by them as having technicians who pass a minimum skill set. And they are at www.natex.org.
You can contact CDC through 404-639-3286. Or the National Center for Environmental health web site. There is very excellent information on carbon monoxide exposures and poisoning all of this information and more is also available on the Consumer Product Safety Commission website.
Morganite
Nov 6, 2006, 01:17 PM
I invite anybody with any doubt about my advice to see https://www.askmehelpdesk.com/heating-air-conditioning/water-heater-problems-40966.html
You will see Northern Heat, a true professional we are lucky to have here, is giving about the same advice as me.
I also suggest anybody that thinks the problem is worn out burners to post that to that thread too.
The only way to know exactly what it is is to have the unit inspected. It is not a problem for a chatroom. The following is from the CDC, who you will recognise, and the discussion from whicht he information is abstracted took place one week ago.
CENTERS FOR DISEASE CONTROL AND PREVENTION
WINTER HOME HEATING HAZARDS
Thursday, October 26, 2006, 12:00 PM
This afternoon, we'll be coming to you to discuss some of the winter home heating hazards that are experienced by most Americans … a joint presentation by the Centers for Disease Control and Prevention, the Consumer Product Safety Commission and the Air Conditioning Contractors of America, highlighting a silent, insidious killer, and a silent public health issue: carbon monoxide poisoning … change the batteries in their carbon monoxide detectors, an important part of the overall preventative approach to carbon monoxide poisoning … We're all familiar with trip and fall hazards, but not enough of us are familiar with carbon monoxide … carbon monoxide … is a silent and insidious killer. It's colorless. It's odorless. It's poisonous. We lose almost 500 Americans every year to [death from] carbon monoxide inhalation, five times as many as we lose to West Nile virus. Non fatal carbon monoxide poisonings, the ones that don't kill people but make them sick send an estimated 15,200 people to emergency departments every year … exposures to carbon monoxide can cause headaches, dizziness, weakness, vomiting, chest pain, confusion, and in some cases, long lasting neurologic damage … Faulty gas furnaces cause more carbon monoxide poisoning than any other source … whenever you burn fuel, you may be creating carbon monoxide. And … you may be exposed to excessive levels of carbon monoxide. Not only gas furnaces need our attention, but gas burning appliances, gas or wood burning stoves, fireplaces, and generators, when they're used in enclosed or semi enclosed spaces … these are preventable deaths, preventable injuries … and taking simple steps can protect you, your family and your pets from carbon monoxide poisoning.
[G]et your heating ventilating and air conditioning system serviced by a qualified technician. That technician should look not only at the furnace, but at water heaters and any other gas, oil or coal burning appliances every year ... appliances that are not working properly are more likely to cause carbon monoxide poisoning … [Glenn Hourahan from ACCA] ACCA is the trade association representing the contractors in the U.S. who install, service, and maintain heating, ventilation and air conditioning equipment. I'm here to support the message coming both out of CDC and CPSC … and to reiterate, the requirements and the necessity to have your home heating systems inspected annually to ensure that they're operating properly. Proper operation will ensure that carbon monoxide is not generating excess levels as well as to ensure that carbon monoxide that is generated within the combustion process is vented. So reiterating the message that has all ready been spoken we strongly encourage that home owners engage the services of qualified contractors to have technicians come to their homes, to have their systems inspected, to make sure they're operating properly, to make sure the venting systems are performing properly. To ensure that other equipment and systems that might be connected to a common vent are working properly. … This might be water heaters.
When having a contractor, a technician come to your home, there are certain things that this technician is doing and there are certain things that consumers should check ensure are being done. One of the most important things that a contractor will do is ensure that the heat exchange does not have any cracks in it. This will prevent carbon monoxide from being directly vented from the combustion process and released into the occupied space.
They are also going to be looking directly at the flue and the venting pipes to ensure that they are sound, no rust, no corrosion, no wholes and no evidence that they might soon be occurring. They will look at the burner assembly as well as the blower assembly to ensure that they are going to be - that the equipment can operate properly and that complete combustion will occur.
There are also a number of measurements and adjustments and cleaning that will be done within the various heating systems and ventilation systems to ensure that they will perform properly. While in the building, a qualified contractor will also look beyond just the equipment itself.
They'll be looking for situations that could cause a very dangerous build up of carbon monoxide in a home … what's called flame rollouts, so the flame on your burner can roll out and cause incomplete combustion.
You can also have backdrafting, either down a chimney as well as down the vent flue from the combustion equipment itself, as a result of pressurization problems. So the contractor will be looking for these situations … it should be recognized that doing this on an annual basis is a good idea, because not only does it reduce carbon monoxide possibility of entering the home, at the same time, it leads to better equipment performance, and reduced fuel use, which is always good as well.
Yes, we strongly encourage that consumers and homeowners look for NATE, North American Technician Excellence, look for those who are certified by them as having technicians who pass a minimum skill set. And they are at www.natex.org.
You can contact CDC through 404-639-3286. Or the National Center for Environmental health web site. There is very excellent information on carbon monoxide exposures and poisoning all of this information and more is also available on the Consumer Product Safety Commission website.
iamgrowler
Nov 6, 2006, 01:20 PM
My water heater is next to my furnace. Gas line is split between them. Furnace is running just dandy. The thermocouple seems fine. The flames don't want to stay on the burner. On the outside of the tank there is a lot of melted plastic and black soot/singe marks on the metal from the flames escaping.
Does the burner or the interior of the burn chamber appear rusted?
Are there white chalky deposits in the bottom of the burn chamber?
An improperly vented hot water heater will cause condensation to drip back down the vent pipe and rust out the burner, and if the burner is degraded, flames will seek the closest source of air, which is the opening where you light the pilot light.
If there are white chalky deposits in the burn chamber, then it was vented into an unlined chimney, and the lime in the mortar is leaching out and dripping back into the burn chamber, which will also degrade the burner.
If either is the case, then the tank should be replaced and proper venting installed.
iamgrowler
Nov 6, 2006, 01:37 PM
I invite anybody with any doubt about my advice to see https://www.askmehelpdesk.com/heating-air-conditioning/water-heater-problems-40966.html
You will see Northern Heat, a true professional we are lucky to have here, is giving about the same advice as me.
I also suggest anybody that thinks the problem is worn out burners to post that to that thread too.
I think the real issue here is that you should refrain from offering up advice outside your area of expertise.
At some point, Labman, your over exaggerated sense of hubris needs to take a step back in favor of qualified experts.
You wouldn't be in the pickle you are in right now if you had simply re-directed the poster to a more appropriate forum from the outset.
speedball1
Nov 6, 2006, 01:45 PM
OK guys! Scale it back. Looks like Northern Heat might have nailed it.
" Check the core of the water heater it may have sooted up. Also fresh air comes in from the bottom of the water heater, a round hole just under the burner, this could be blocked with rust and stuff, look for other openings or screens if this is whats called a sealed combustion water heater."
This might be a venting or a air flow problem. In my area most of our appliances are electric so I've stayed out of this exchange but it's getting rather deep and it's not good for the askers to witness two experts bickering.
I don't care who's right or wrong. Morganite, you've voiced your concerns, No need for insults. Lab, give it a rest and move on.
Guys, this isn't the Religion or Relationships page where emotions run high. We give out technical advice. Let's act like technicians. Now, let's cool it before the mods or Admin stop by with a big stick. I consider both of you competent and well versed in your fields. Let's see what Northern Heats advice does toward solving this problem. Regards to you both and fa Gawds sake kiss and make up. Tom
iamgrowler
Nov 6, 2006, 01:57 PM
OK guys! Scale it back. Looks like Northern Heat might have nailed it.
I don't know, Tom, considering that approaching Labman privately over bad or dangerous advice, as I once tried to do, went over like a fart in church, I'd say that Labman having his butt publicly flogged was long overdue.
Just my 2pence.
ipcfarm
Nov 6, 2006, 02:42 PM
I have a definitive answer: My water heater imploded. Thanks to all of you for help, it is much appreciated.
speedball1
Nov 6, 2006, 02:59 PM
I have a definitive answer: My water heater imploded. Thanks to all of you for help, it is much appreciated.
To say nothing of the accompanying floor show. In all my years I've never heard of a heater imploding. Must have been a hellish vacuum in the pipes.
I think it was ipcfarms patience that imploded.
labman
Nov 6, 2006, 04:54 PM
It is commonly known that shutting the inlet off with cold water in the tank and leaving the gas on will at least activate the safety pressure relief valve if not worse unless you open a hot water tap. If you shut the inlet and gas off on a warm tank, The water is going to contract. Again, something is going to give. Somehow, the volume is going to be reduced. Guess the safest thing is an expansion tank and no valve between.
If you have a blocked vent, a new tank won't fix it. My neighbor once kicked a football down my chimney. Fortunately it found its way to a fireplace not in use at the time.
ipcfarm
Nov 6, 2006, 05:32 PM
I have never heard of one imploding either. Apparently everyone else has, including the manufacturer, the city water department, and both plumbers who came out. The 1st plumber who came out said he had only seen 3 in over 40 years.
letmetellu
Nov 6, 2006, 08:58 PM
A water heater gas valve no mater what the age can malfunction and one of those malfunctions is the valve does not close completely and leaves a small flame burning down at the orifice of the burner therefore it does not collect any air with the gas and so it creates lots of soot and this soot will build up on the underside of the burner clogging the ports of the burner. When this happens and it is time for the heater to heat again the valve opens sending gas out of the orifice but it has nowhere to go. It hits the bottom of the burner and creates a wild fire down in the combustion area of the heater, after a few firings like this and you have incomplete combustion and therefore it will be causing carbon monoxide gas. Spend the $100, get it checked and possibly save a life.
Airwren
Nov 7, 2006, 06:11 AM
I would have to agree this is a potentially dangerous situation, that should be tested properly. Combustion air, manifold pressure line pressure, exhaust. I don't think that unless you have the experience, and the equipment that you should be dealing with flame roll out etc. A thermocouple is one thing, this is another
ipcfarm
Nov 7, 2006, 11:51 AM
It's called thermal expansion.
I hope I can find someone QUALIFIED to do the job.
http://www.hotwater.com/bulletin/bulletin45.pdf
http://www.hotwater.com/bulletin/bulletin41.pdf
http://www.bradfordwhite.com/servicebulletins/105_reliefvalves.asp
labman
Nov 7, 2006, 12:27 PM
I have to apologize to you. I thought about warning you about the danger of closing the inlet valve, but didn't. Too bad those shrieking about CO didn't think to either. Some still seem to be beating a dead horse. Even if you called a professional, the thing may have still imploded before he got there.
Problems from expansion are more common, but as you found out, water contracts too. In the past, water could cycle in and out of a hot water tank with the temperature with no problem, going back the supply line either to the city main, or the pressure tank in a well system. There can be problems with water returning to public water systems. The back flow preventers fix that problem, but create a new one with the hot water heater. The best solution is an expansion tank just before the water heater. And as your reference points out, some other devices can cause the problem too. Shutting off the inlet adds the problem of contracting.
Too bad none of us thought to warn you. In the other thread, Northern Heat may have been on to something about the blocked inlet. Of course, the screened air intakes are screened just to prevent flames from coming out through them.
Replacing a water heater isn't much of a job. Even adding an expansion tank if you need one and putting it up on a stand if in a garage isn't that much more. If you have a flex gas line on it make sure it is the newer plastic coated ones, more reliable than the older ones.
And as I mentioned, if the problem was a blocked vent, it will need to be cleared before the new tank will work right.
Morganite
Nov 7, 2006, 01:33 PM
People often wonder what causes a rumbling sound in their water heater. The two most likely scenarios are breakage of the dip tube and sediment leakage. In the first scenario, the dip tube in the cold water supply inlet is supposed to run to within three or four inches of the bottom of the water heater.
When you turn on the hot water, it forces cold water to the bottom of the heater, which drives hot water out of the heater. If that dip tube deteriorates or breaks off half way into the tank, the capacity of hot water is cut in half, and the cold water meets that hot water, thus causing the rumbling sound.
The second circumstance occurs when the water in the tank is not being heated, some water may leak down through the sediment at the bottom of the tank. This sediment is the result of cold water being heated combining with the various particles settling in the bottom of the tank. When the water is fired up, these drops of water become super heated, and under most circumstances will stay there until some water is used, decreasing the pressure in the tank. These super-heated droplets then exit the sediment entering the tank water as steam and then condense or implode, which cause the rumbling noise.
The drain valves near the bottom of the water heater are generally somewhat off the bottom of the tank, which makes it impossible to drain off sediment.
Repairing existing metallic water piping with plastic tubing can also create an electrical shock or fire hazard and possibly ruin the electrical appliances and electronic devices attached to the wiring because of the plastic piping, especially if the metal pipes were used for the grounding of electrical services.
The electrical service in a structure needs to be grounded in order to make all of the electrical appliances and electronic equipment in your house work properly as well as limit the chance of electrical shocks and fires. In older homes the main ground wire was not always run back to where the water service entered into the building as it is done today. It was merely attached to the nearest cold water pipe that was accessible to the electrician at the
Time. So if you are repairing or adding on to existing metallic water piping with plastic tubing you must consult a qualified electrician to make sure that you are not exposing yourselves to undue hazards.
Be safe - engage a qualified and certified professional. Gas lines and electrical connections are no place for amateurs.
M:)RGANITE
iamgrowler
Nov 7, 2006, 02:43 PM
It's called thermal expansion.
I hope I can find someone QUALIFIED to do the job.
http://www.hotwater.com/bulletin/bulletin45.pdf
http://www.hotwater.com/bulletin/bulletin41.pdf
http://www.bradfordwhite.com/servicebulletins/105_reliefvalves.asp
I don't mean to split hairs, but thermal expansion would create an explosion, not the implosion diagnosis you presented earlier.
speedball1
Nov 8, 2006, 05:26 PM
I'm on Growlers side, "thermal expansion would create an explosion, not the implosion diagnosis you presented earlier."
I want someone to explain to me how a water heater under 45 pounds of pressure could "implode". Implosion implies a suction or external pressure so huge it causes the tank to blow inward. Where does this super amount of suction come from?
Ipcfarm sez,"I have never heard of one imploding either. Apparently everyone else has, including the manufacturer, the city water department, and both plumbers who came out. The 1st plumber who came out said he had only seen 3 in over 40 years"
I want to contact the city water department, the manufacture or the plumbers who say they have found a way to reverse the natural laws of physics" Signed, Puzzled in Sarasota.
labman
Nov 8, 2006, 07:35 PM
Seal a container of water and cool it, you will get a vacuum. However, the 15 psi atmospheric is the most you can get, and that would be less the vapor pressure of water. I would expect a tank with a design of 150 psi would take less than 1/10 of that in vacuum. I am not sure what happened. Be nice to hear more from ipcfarm.
I remember as a kid, putting a little water in a square gallon can, putting it in a fire, and then pulling it out and tightening the lid. We then watched it implode.