- flow measurements (0 replies)
- Is there any effect if we put recycle stream to CSTR ? (1 replies)
- How do I determine the height of a supply tank to a pump that has the following specs (0 replies)
- Mono hexene HDPE (1 replies)
- Converting co2 into carbon and oxygen (0 replies)
- Percent excess air (3 replies)
- Mass balance of cigarette smoke odor (2 replies)
- Acid separation process (1 replies)
- Diesel solidification (0 replies)
- An ultra filtration membrane having pore diameter 70 A (0 replies)
- Shocking or not (0 replies)
- Calculate net pressure of floating roof on the liquid (0 replies)
- Radioactivity (1 replies)
- Angle of repose (0 replies)
- What is the best gel material for wrist rest/palm rests (1 replies)
- Permanently remove of the Pipeline Insulatation (0 replies)
- Co2 sequestration (0 replies)
- Concentration of Unknown solution (0 replies)
- Need help with this question! (2 replies)
- Effect of Humidity on fuel consumption in furnace (0 replies)
- How we make 0.01m of EDTA sol (1 replies)
- Method to calculate hardness in water (1 replies)
- Plant Utilities Boiler condensate recycle (0 replies)
- We have a cstr in which the following parallel reactions take place. R->Y, R->Q, R->Z (0 replies)
- Numericals of thermodynamics workdone calculation according to linear law (0 replies)
- Process Balance (1 replies)
- Hi I have a problem.I wanted to know as to what exactly is the reason for the corro (0 replies)
- What's the meaning of thi in chemistry? (0 replies)
- What is the meaning of this symbol? (2 replies)
- Internal flow (3 replies)
- I need sample letter for introduction for new sales for chemical company? (1 replies)
- Resin letter (1 replies)
- Interpolation (1 replies)
- Fluid Mechanics(Mass Balances)2 (2 replies)
- Fluid Mechanics(Mass Balances) (11 replies)
- Trying to compress pulp slurry (0 replies)
- Suggest a material which is bio-compatible [more to follow] (1 replies)
- THis chem eng process balance question is bugging me, need some help! (0 replies)
- Material balances question (5 replies)
- Homework help (0 replies)
- Brush plating challenge (2 replies)
- Brush plating challenge (0 replies)
- How to prepare company profile for chemical products (0 replies)
- Pressure difference (2 replies)
- How can steam be separated from slurry for steam recovery? (0 replies)
- How to calculate the production rate of dry milk from spray drying process? (0 replies)
- Stirrer for epoxy resin (0 replies)
- Process Control (0 replies)
- Steady state flow process (0 replies)
- Can anyone help me with oil and gas production methods and its challenges? (1 replies)
- Us university with low gre score (0 replies)
- Basic differences between PVC and ABS in stationary productions (0 replies)
- How & what are recycling process/system in lead acid batteries? (1 replies)
- What are alternatives of lead in batteries? (1 replies)
- Why lead is used 4% with Aluminium in winfow lever & gear? (1 replies)
- Pressure drop across reducers (4 replies)
- On oil and gas platforms a cold vent is used instead of venting or purging. What is (0 replies)
- Cold vent (0 replies)
- Water treatment and pH correction with acid (0 replies)
- I am good student but cannot concentrate on my studies now a days (0 replies)
- Health risk: freon's oxidation and/or degradation products? (2 replies)
- Question chemical engineering ask (0 replies)
- I want to prepare chemical trading company introductory letter (2 replies)
- What ishydrate? (1 replies)
- What is the best way to bond Unplasticed PVC to ABS (Acrilo-Butile Styrene)? (1 replies)
- What is potassium dichromate maximum wavelength using UV specrophotometer? (3 replies)
- What is compressibility factor with respect to pressure and temperature (0 replies)
- How to get Enthalpy-concentration data (0 replies)
- Iron corrosion (0 replies)
- Exploding coffee (0 replies)
- Calculate the energy in joules and calories (0 replies)
- Heat of vaporization (1 replies)
- Nitrogen volume calculator (1 replies)
- Step it would take to walk fron earth to alpha centuri (0 replies)
- How to clean chemical mixing containers (1 replies)
- How to introduce in an interview in an impressive way (1 replies)
- Flash Drum Or Knock out Drum (2 replies)
- Amount of nitrogen for testing pipe (7 replies)
- Sewer Gas (1 replies)
- Self ignition temp. (2 replies)
- What really happens when (1 replies)
- Single ideal reactors and batch reactor (1 replies)