|
|
|
|
New Member
|
|
Dec 20, 2006, 10:46 PM
|
|
Sewage ejector pump
I think my sewage ejector pump may be bad. The fuse for the pump popped and when I re-set the breaker, the ejector pump turns on for several seconds and then the breaker pops again. Does that mean the pump is gone bad or do I have an electrical problem.
|
|
|
New Member
|
|
Dec 20, 2006, 10:58 PM
|
|
It's most likely an electrical problem. You have a dead short or overload somewhere on that circuit. That is why your breaker trips. Sounds most likely to be a short, since it only takes a matter of seconds for the breaker to trip. This does not mean that the pump is good, because there could be a short somewhere in the cord or windings of the motor for the pump.
The fuse that popped, it was on the pump correct? I just want to make sure you're not referring to the circuit breaker.
|
|
|
New Member
|
|
Dec 20, 2006, 11:15 PM
|
|
Just to clarify, it was the circuit breaker that pops. Also, 2 days ago my water softner was regenerated over night and kept regenerating causing a minor flood in the basement. I turned off the softner and later discovered the circuit breaker for the ejector pump had tripped. I re-set the breaker and it was working fine until today.
|
|
|
New Member
|
|
Dec 20, 2006, 11:47 PM
|
|
It almost sounds like the ejector pump has something in the catch basin it can't handle, and is overheating from the lack of flow. Have you checked the basin to see if there's anything that got down there that shouldn't have?
My only other guess at the moment would be that the receptacle (if plug-in) or the junction box got wet during the flood (which caused a short), and it's still not dried out, or the cable to the pump somehow frayed and is giving you an intermittent short.
Is this a GFCI outlet (or protected by one) or breaker? If so, test it and make sure it is functioning correctly.
|
|
|
New Member
|
|
Dec 20, 2006, 11:55 PM
|
|
The panel is a GFI and it did not get wet. I think there may be something caught in the pipe as I did pull out a piece of copper tubbing and a matchbox car the other day. There may still be something caught up in there I can't see. I will call a plumber. Thank you for your help.
Doug...
|
|
|
New Member
|
|
Dec 21, 2006, 12:00 AM
|
|
My pleasure Doug, glad I could help. Please do report back and let us know what it was!
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Sewage Ejector Questions
[ 4 Answers ]
I have a workshop located behind my home. The shop is currently using a very old and failing septic system. I would like to use a sewage ejector to pump the wastewater from a toilet, sink and shower (minimal use) in the shop up to the city sewer line that the home is attached to. The shop bathroom...
Sewage Ejector Pump in a Basement
[ 9 Answers ]
Hello all
I am new to this board so forgive me if this has already been asked. I am in the process of adding a basement to our basement. We have a septic system with the discharge pipe about 3 feet above the floor. Several questions. I want to add a Toilet, sink and tub. What all has to be vented....
Ejector Pump?
[ 3 Answers ]
We just bought a new house that has an ejector pump. I don't know anything about them and have a few questions for anyone with knowledge on the subject:
Can you use a standard kitchen garbage disposal with ejector pumps?
Can you flush baby wipes or feminine products?
How often do the...
Sizing sewage ejector
[ 2 Answers ]
I am owner/builder in design stage of a new 'log' cabin with basement and just got to plumbing. I will of course hire a plumbing sub-contractor but want to avoid total redesign by 'understanding' enough basics to get it OK on my floor plan. I will post the drain and venting questions as a separate...
View more questions
Search
|