Ask Experts Questions for FREE Help !
Ask
    kadecg's Avatar
    kadecg Posts: 2, Reputation: 1
    New Member
     
    #1

    Mar 5, 2006, 09:21 PM
    Kenmore dryer runs but does not heat
    My Kenmore dryer just stopped heating but it runs.
    The model number no is 110.62994101.
    I need help on how to fix it. If possible with diagram on
    How to change any part.
    applguy's Avatar
    applguy Posts: 324, Reputation: 23
    Full Member
     
    #2

    Mar 6, 2006, 05:33 PM
    This is basically a Whirlpool 27" dryer. First, you must check your household fuses or circuit breakers. Electric dryers need two separate lines of voltage in order for the heater to function. Sometimes one fuse or breaker will open, leaving you with a dryer that will run but won't heat. To be sure, replace the 30 amp fuses or turn off the breaker and then back on. If it still doesn't heat, it could be thermostats, cutoffs, or simply a broken heater. If the fuse/breaker thing doesn't work, we can continue from there.
    kadecg's Avatar
    kadecg Posts: 2, Reputation: 1
    New Member
     
    #3

    Mar 6, 2006, 06:11 PM
    Thanks
    The element is broken and I need to change it. The part no is 3387747.
    Can you give me a step by step illustrations on how a change it.
    applguy's Avatar
    applguy Posts: 324, Reputation: 23
    Full Member
     
    #4

    Mar 7, 2006, 05:02 PM
    First, make sure the dryer is unplugged from the outlet, of course. Usually the only way to know that the element is physically broken is to take it out and look at the whole thing. I'm slightly confused about how you know it's broken without already having it out. Anyway, the heater is in a horizontal tube behind the lower access panel. Open the panel by inserting a putty knife or similar object into the gap above the lower panel and apply pressure to the top of the black clips and pull out on the upper part of the panel. It will hinge down. The heater tube is on the right side. Simply disconnect the wires leading to the various thermostats and cutoffs on the left side (there are several, and make sure you remember which wires go to which parts) and remove the 1/4" screw holding the metal flap in front of the heater tube opening. Then remove the 1/4" screw holding the front tube support. The heater will then pull straight out towards you. The old heater pulls out of the can (look for a screw holding it in), and the new one replaces it. Simply reassemble the parts, making sure the heater tube goes inside of the duct in the rear, not just against it. Good luck.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Kenmore Dryer - heats & runs but stops mid-cycle [ 12 Answers ]

I have been trying to figure out what exactly is up with our Kenmore dryer. We bought it new in 1997 and it has run like a champ till now. It still heats up and the drum still tumbles. In the regular drying cycle - you set the timer for 60 minutes and about 15 minutes into the cycle, the dryer...

Kenmore Gas Dryer won't heat after 5 minutes [ 2 Answers ]

Hi, My Kenmore Gas dryer, over 12 years old, model # 110.8754 5100, ignites and blows gas just for few minutes and stops burning. The drum is still running. I turn it off and wait for 15 minutes until the temperatur goes down. I turn the dryer back on and it blows gas and burns again. Just...

Kenmore Elite Dryer won't heat [ 16 Answers ]

I have a heavy duty Kenmore Elite dryer for about 5 years (bought new) but it doesn't heat now. Power works fine. The inside part turns/tumbles fine. Light works when you open the door. We clean lint out each time. Just doesn't heat on any of the dial settings. I've switched power at the...

Kenmore dryer help / No heat [ 2 Answers ]

I have a Kenmore 80 series Super capacity plus dryer. Model# 77832791 77832 that is not heating. Sounds like after it runs for about 30 seconds that it is trying to fire up but then doesn't. I consider myself to be handy and could probably fix it with some help. Any idea where I should start? Does...

Kenmore dryer: how long should heat cycle? [ 1 Answers ]

Hello, This is my initial post to this forum and hope someone out there can help. I own a Kenmore dryer (87984800) that is about 12 years old. Recently, it has begun to take two cycles to dry a medium-large load of clothes. This is unusual for this dryer. The dryer is doing the following:...


View more questions Search