Ask Experts Questions for FREE Help !
Ask
    sturoc's Avatar
    sturoc Posts: 38, Reputation: 1
    Junior Member
     
    #1

    Mar 13, 2005, 01:33 PM
    OS interrupt
    Hello,
    Have P II ,266 Sometimes when using program like Nero or just any normal windows app Screen goes blue and this message in text appears at top of screen:
    "stop- inpage - kernel - error" "begin physical dump of memory"
    Plus a series of numbers.
    Have not been able to copy all #'s down cause PC shuts down at that point. Then upon start up half the time it says "O S not found".
    I shut down, restart then it boots up fine.
    Any Ideas?
    Thnks
    psi42's Avatar
    psi42 Posts: 599, Reputation: 13
    Senior Member
     
    #2

    Mar 13, 2005, 02:06 PM
    Interesting. I have a few ideas.

    Basically we need to differentiate whether this is a software problem or a hardware problem. You can try downloading this cd and booting from it to see what the tests have to say about your system.

    Without that information, here are a few general ideas:

    Your OS may just be a little off in the head. Have you done the usual defrag/scandisc/antivirus/antispyware routine?

    Your RAM may be bad. This can cause the system to crash randomly. Try memtest86. I would test this one first.

    Your system may be overheating. Try increasing ventilation by blowing out fan ducts with a can of compressed air (hopefully you can snag one at a local office supply/computer store). You could also try removing the case cover (this will expose the system to possible electrostatic discharge and lots of dust, so be cautious if you decide to go this route. )


    ~psi42
    fredg's Avatar
    fredg Posts: 4,926, Reputation: 674
    Ultra Member
     
    #3

    Mar 15, 2005, 07:10 AM
    Freezing Up
    Hi,
    Are you using Win98/98SE? This is somewhat of a common problem with System Resources with 98.

    If you are using 98, here are maintenance steps to perform, which contain many of what was suggested by PSI42:

    I would do the Registry Repair, just in case part is corrupted. There is no harm in doing it. Then, do the Scandisk, and Defrag.

    Registry Repair should be done whenever there are problems:

    To Repair the Registery:
    Turn off the computer; or reboot; then immediately press F8, (or, could be F5) located on top of the keyboard. Keep it press down until an options window comes up, then release it.
    (If F8 or F5 doesn't work, then re-boot, and immediately press down the CTRL key, hold down until it comes up to the options screen).
    Use the up and down arrow keys on the keyboard to select "Command Prompt Only".
    Press Enter
    You will now see C:>
    Type in SCANREG /FIX (there is a space between the G and the / ).
    You will now see C:>SCANREG /FIX
    Press Enter
    This will take about 5 minutes or so.
    When finished, press Enter for OK.
    Manually, turn off the computer, wait a few seconds, the turn it back on.
    If you don't have the "Command Prompt Only" option, then re-boot the computer normally.
    Go to Start/ShutDown, then choose "restart in ms-dos mode".
    It will come up to C:\windows.
    Type in CD C:\
    It will look like C:>windows CD C:\
    Press Enter.
    It will then be at the C:> prompt.
    Then type in SCANREG /FIX
    Press Enter
    When it returns to the C:> prompt, then manually turn off the computer, and turn it back on.

    Win98/98SE Regular Maintenance
    All of these should be run whenever Win98/98SE starts giving problems. It will keep the computer running smoothly.

    Before doing any of the following; turn off wallpaper and screensavers before re-starting or re-booting the computer.

    Safe Mode is best where indicated, because most programs are not running meaning their files are closed, or not in use. This allows them to be scanned much better, repaired, or defragged better.

    1. Scandisk
    Start in Safe Mode by:
    Re-boot the computer, and immediately after starting up, Press and hold down, F8, at top of keypad.
    When the options show on the screen, use the up and down arrow keys on the keyboard to select
    "Safe Mode".
    Press Enter
    After it boots to Safe Mode, go to Start/Programs/Accessories/System Tools, and click on Scandisk.
    (It is faster if set on "Standard", the "Thorough" usually is not needed and takes a long, long time).
    Click on "Start" and let it run until finished.

    2. Defrag
    When Scandisk is finished, click on "Close".
    Now, go back to the same place, but this time, click on "Defrag".
    Click on OK, and wait until it finishes (might take 1 hour if not done within a month).
    After it finishes, Click on OK or whatever.
    Then, re-boot.

    The following Boot Disk has to be done only one time.

    Also, a "must have" is a Boot Disk, for Win98/98SE. One never knows when the computer might not load windows and go to the desktop... it does happen.

    Here are steps to make one:

    Insert the Win98/98SE CD in the CD-ROM drive.
    Go to Start/Programs/Windows Explorer
    Double click on D:/ , if that is your CD-ROM drive letter.
    Find and open the folder; Tools/Mtsutil/Fat32ebd (stands for Emergency Boot Disk)
    Double click on the file Fat32ebd.exe and follow the instructions to create the Boot Disk.
    Then remove the CD from the CD-ROM.

    Now, we must test the Boot Disk to see if it works.
    Shut down the computer; then turn it back on with the Boot Disk still in the computer.
    When a screen comes up, use the up and down arrows on the keyboard to select "Boot with CD-ROM support". Then press Enter.
    It will show some things about the computer, and then come up to the A:> prompt.
    Now, insert a CD (any will do) into the CD-ROM.
    Wait until it "spins" and the light goes off.
    Now, at the A:> prompt, type in DIR D:
    It will now look like A:>DIR D:
    It should show all the files on the CD.
    If so, the Boot Disk is good. If NOT, repeat all the above.
    If it's good, then remove the CD, manually turn off the computer, and remove the Boot Disk. Turn on the computer and it's ready to go.

    Here are some "tweaks" for Win98/98SE that really work well.

    Win98SE Tweaks for better performance
    http://www.speedguide.net/read_articles.php?id=170

    To extract files: here are steps:
    Extract the following from c/cabs/cab53 and cab54.
    (Right click on a Cab, then left click on View).
    To extract a file then seen, Right click on the file,
    Then Left click on Extract.
    Vcomm.vxd
    Vdmad.vxd
    Configmg.vxd
    Vdd.vxd
    Vmouse.vxd
    Ntkern.vxd
    Vflat.vxd
    Extract to:
    c/windows/system; and also to:
    c/windows/system/vmm32.

    Win98SE USB Updates:
    http://www.usbman.com/win98seusbguide.htm

    Also, for Win98/98SE; any ONE of the following programs WILL, normally, cause problems:
    1. Microsoft's DirectX 9.0c
    2. Sun Java; any versions, such as j2re 1.4.1 or 1.4.2. (use the Tools, Internet Options, Advanced tab, under the heading "Java VM", the only check mark should be by "JIT compiler for virtual machine.....".
    3. Microsoft's Internet Explorer & Outlook Express Cumulative Security Patches from Windows Update.

    After you use Nero, if you are burning a CD-R, etc, re-boot the computer before you burn the next one. This will help restore the System Resources to high again.

    Just for information:
    If you wish to add or subtract from an Experts' reputation, or show appreciation or discontent with an answer, click on the "balance scales" icon across from the Experts' name on the right hand side of the page. You can then choose what you wish.

    Best wishes,
    fredg
    thebriggsdude's Avatar
    thebriggsdude Posts: 1,096, Reputation: 53
    Ultra Member
     
    #4

    Mar 16, 2005, 12:46 AM
    I'm leaning to what psi42 said. Plus yes it may be overheating as well, compresed air may help but not as good as removing the fan and cleaning it with a hard brush then using the air. Also you could have a problem where the memory is bad, plus you could try and make sure your connections are good inside

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.



View more questions Search