Ask Experts Questions for FREE Help !
Ask
    irmanator's Avatar
    irmanator Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Aug 6, 2010, 08:44 AM
    Honeywell TH8000 thermostat questions
    After programming Heat set to 70 and Cool set to 78...
    When exactly do these functions kick in and turn off?
    And what median temp can you expect... 74?
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #2

    Aug 6, 2010, 09:07 AM

    Perhaps this will help

    http://www51.honeywell.com/pacific/c...ionPRO_Use.pdf
    irmanator's Avatar
    irmanator Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Aug 6, 2010, 09:26 AM
    I have both the user guide and operating manual. They don't appear to answer my question.
    wmproop's Avatar
    wmproop Posts: 3,749, Reputation: 91
    Ultra Member
    		  
    #4

    Aug 6, 2010, 09:35 AM

    I`m not experanced with the th8000,but seems to me they both should cut off at the set point
    Heat cuts off at 70
    Cooling cuts off at 78

    Not sure I`m understanding your question
    Don`t think you can have them both set at the same time,for a median of 74 or any other degree
    NorthernHeat's Avatar
    NorthernHeat Posts: 1,455, Reputation: 132
    Ultra Member
    		  
    #5

    Aug 6, 2010, 02:37 PM

    Your house will stay between 70 and 78. Over 78 the air will come on cooler than 70 the furnace will kick on, that is if the thermostat is set to auto mode.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
    		  
    #6

    Aug 6, 2010, 07:52 PM

    "auto mode" is defined as "auto changeover"
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Honeywell th8000 [ 10 Answers ]

I have a th8000 that is locked up. I have tried new batterys I have also tried to pull the memory battery out and still nuthin I bought this house about 6 months ago and it came with it, is there any way of getting it unlocked, these aren't cheap units if not ill go with something else, also does...

Miller thermostat change to honeywell visionpro serie th8000 only have 2 wires [ 1 Answers ]

How do I setup the honeywell with only 2 wires? 1 wire was hooked to W and 2nd wire was hooked to R on old one.

Programming Honeywell VisionPRO TH8000 thermostat [ 1 Answers ]

How do I go about entering the temperature for my backup heat source (in my case, gas) to kick in? I believe it was set at 35 degrees, but I want to confirm. Thank you

Honeywell TH8000 thermostat [ 3 Answers ]

This thermostat was installed only 8 months ago and has worked fine until last night. It began a humming sound and the thermostate vibrates. What is causing this? The heater is working fine and all displays are normal. It is just this loud sound that is emitting from the thermostate itself and...

Honeywell TH8000 Thermostat [ 8 Answers ]

When this thermostat call for aux. heat, it reads aux. heat on the pad but no heat. The aux. heat works in manual mode. I think a setup code is wrong since it has never done right. Could someone help.

View more questions Search