Ask Experts Questions for FREE Help !
Ask
    dsmall's Avatar
    dsmall Posts: 2, Reputation: 1
    New Member
    		  
    #1

    Oct 24, 2009, 01:34 PM
    No gas to the furnace
    Carrier Crusader Gas furnace 19 years old
    Will not flame up when the glow plug lights up. Technician just left $75 to tell me I need a new circuit board #CES0110057-00 and $350.00
    My question is is that a fair price and do you believe I need a new board.

    David
    scooterVA23692's Avatar
    scooterVA23692 Posts: 3, Reputation: 1
    New Member
    		  
    #2

    Oct 28, 2009, 06:23 PM

    I have the same problem. I have a Carrier 58RAV055-GC with circuit board CEES0110057-00. So far I see the board for sale on the internet at various locations for $170 to $230. I tested my gas valve and the various safety switches and everything looks good so far.-but the gas valve never gets the signal to turn on after the 'glow plug' lights up. I suspect it is the board.
    scooterVA23692's Avatar
    scooterVA23692 Posts: 3, Reputation: 1
    New Member
    		  
    #3

    Oct 28, 2009, 06:28 PM

    FYI: I see that there is a Nov.2007 post by 'DWF' that writes about the same kind of problem. The response was that the board is bad.
    hvacservicetech_07's Avatar
    hvacservicetech_07 Posts: 1,083, Reputation: 75
    Ultra Member
    		  
    #4

    Oct 28, 2009, 09:37 PM

    It is very possible that the circuit board is bad, the only way to know for sure is with a voltage meter. That price seems kind of high.
    dsmall's Avatar
    dsmall Posts: 2, Reputation: 1
    New Member
    		  
    #5

    Oct 29, 2009, 09:06 AM
    Replaced the circuit board ($175) and it works fine. Thanks for the response.
    scooterVA23692's Avatar
    scooterVA23692 Posts: 3, Reputation: 1
    New Member
    		  
    #6

    Nov 4, 2009, 08:47 AM

    FYI: I replaced the circuit board on mine also ($177 w/shipping) and now it works fine. Thanks for the input.
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Goodman furnace GMNT080-4 furnace runs good for a while then has to be manually reset [ 5 Answers ]

I have a Goodman GMNT080-4 (90%). I'm having the same problem As Streatherg did back in the Nov 2006 question. I reviewed his article and tried Every thing on there but seems to be doing the same thing. The furnace kicks on for about an hour then locks out and has to be manually reset threw...

Add on coal/wood furnace thermostat wiring for 2 zone house with oil furnace [ 1 Answers ]

I purchased a Harman wood / coal furnace model SF-2500 (forced hot air system) and am tying into my existing forced hot air oil furnace 2 zone system and do not know how to tie into the existing thermostats and zones. I wish to still use the 2 separate zones for the bedrooms and the main body of...

Furnace ignites but blower won't start till furnace shuts down. [ 7 Answers ]

(Nordyne/Miller G3RA)-I have a furnace HSI(glow plug) that will ignite and burn until it gets too hot and shuts down. As soon as the furnace shuts down the blower starts to circulate air. The blower circulating air cools the furnace and it reignites.Shortly after the furnace ignites the blower...

Furnace not heating the house. Damper on the furnace not opening. Motor then shuts. [ 4 Answers ]

My forced-air furnace is not working correctly. The gas works heating the air in the furnace, but When the motor starts the damper doesn't open and the Motor shut down. I need suggestions?:mad:

Comfortmaker Furnace Fan blows in line fuse and will not allow furnace to work [ 1 Answers ]

I have a Comfortmaker Furnace (approximately 1998/99) and the fan will not turn on allow the furnace to heat. When I try to turn the furnace on it blows a 3 amp fuse at the blower motor. I removed the fuse and jumped it and all it will do is make a faint buzzing noise and not turn on. I can...

View more questions Search