Ask Experts Questions for FREE Help !
Ask
    jacmac's Avatar
    jacmac Posts: 10, Reputation: 1
    New Member
     
    #1

    Sep 2, 2008, 04:48 PM
    Is my weedwacker seized?
    I was using my $200.00 weedwacker today and it suddenly stopped. Tool is about 2 years old. I tried to pull rope to get it restarted and rope will not move. Is my engine seized?
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #2

    Sep 2, 2008, 04:59 PM
    Do you mix oil with the gas?
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #3

    Sep 2, 2008, 06:47 PM
    Remove the spark plug and tell us if you can pull the rope. Look into the hole with a flashlight, tell us what you see. I hope Stratmando is wrong going down this road. It will get expensive if he is on the right track.
    jacmac's Avatar
    jacmac Posts: 10, Reputation: 1
    New Member
     
    #4

    Sep 3, 2008, 05:04 AM
    Yes I mix oil with gas, in fact I may have put too much oil in. Can too much oil ruin my engine? I will take out spark plug and look at it today. Thanks
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #5

    Sep 3, 2008, 08:07 AM
    Oil much oil can cause it to not start but it should not cause it to seize like you described. Tell us what you found when you pulled the plug.
    KISS's Avatar
    KISS Posts: 12,510, Reputation: 839
    Uber Member
     
    #6

    Sep 3, 2008, 09:28 PM
    Lots of dirt on the cooling fins will cause this from lack of cooling.
    jacmac's Avatar
    jacmac Posts: 10, Reputation: 1
    New Member
     
    #7

    Sep 11, 2008, 03:41 AM
    I took the plug out. It is black/grey. Peeked inside and that is black/grey also. Looks burned up to me.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #8

    Sep 11, 2008, 04:09 AM
    See If you can pull the side cover and see if it can turn by the bolt on the end of the shaft.
    Many 2 strokes LOOK like they are burned up.
    jacmac's Avatar
    jacmac Posts: 10, Reputation: 1
    New Member
     
    #9

    Sep 13, 2008, 09:21 AM
    I am not sure what you mean I should do.
    ballengerb1's Avatar
    ballengerb1 Posts: 27,378, Reputation: 2280
    Home Repair & Remodeling Expert
     
    #10

    Sep 13, 2008, 10:27 AM
    This engine may be shot so lets try some unorthadox approaches. Pull the plug and spray a heavy dose of WD 40 or liquid wrench into the combustion chamber, soak for a while and then try to pull the rope.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #11

    Sep 13, 2008, 12:10 PM
    I was saying, if somehow you could try turning engine over, other than with a rope to determine if pull assembly is jammed and at fault and hopefully not the engine.

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Weedwacker engine on a bike [ 7 Answers ]

How would you rig up a weedwacker engine to a wheel of a bike?

Weedwacker vibration [ 1 Answers ]

My weedwacker has a terrible vibration on the spool end when its running. It runs fine and then will vibrate really bad then it'll stop vibrating.

Sears weedwacker 32cc [ 1 Answers ]

I have a sears weedwacker 32cc. Model #358-791590. The pulley string on the inside of the motor assembly has broken. My question is how do I get the pulley off in order to replace the string assembly. I have taken out all the bolts from around the casing.

Right oil,gas ratio to mix for weedwacker [ 1 Answers ]

I have a Homelite Gas & Oil Weed wacker. No instructions. I need to know the gas and oil ratio??

Weedwacker [ 4 Answers ]

I need to buy a new one. Any advice?


View more questions Search