![Ask Experts Questions for FREE Help !](custom/vgo/images/amhd_logo_os.png) |
|
|
![jchild40's Avatar](/images/avatars/default_avatar.gif) |
New Member
|
|
Jan 9, 2009, 06:23 PM
|
|
Whirlpool top load washer lsb6300lw1
I have a whirlpool top loader that does not like to spin. If I open the lid, hold down the switch while it's on the spin mode, THEN help it start spinning, it will take off. It does not seem to want to begin spinning on it's own.
I did replace the clutch, hoping that was the problem. Before I did this, it wouldn't spin at all, even with my help.
It does not have any issues agitating or draining.
I wonder if I have to replace the gear box?
|
|
![pokefan7790's Avatar](/images/avatars/default_avatar.gif) |
Junior Member
|
|
Jan 10, 2009, 08:25 AM
|
|
Check to see if the drive block is slipping on the spin tube.
|
|
![jchild40's Avatar](/images/avatars/default_avatar.gif) |
New Member
|
|
Jan 10, 2009, 08:58 AM
|
|
![Quote](custom/vgo/images/misc/quote_icon.png) Originally Posted by pokefan7790
Check to see if the drive block is slipping on the spin tube.
I'm an amateur washing machine fixer upper... not sure what those are, even though I've had this machine torn down a couple times. Here is a site that has all the subcomponents, maybe you can point out what your talking about?
|
|
![ShadyLady's Avatar](/images/avatars/default_avatar.gif) |
Junior Member
|
|
Jan 10, 2009, 05:15 PM
|
|
In order to get to the drive block you have to take off the agitator, the spanner nut, and the inner basket. You will then see a somewhat "bell" shaped metal piece that goes over the tube and agitator shaft. Usually the drive block is on extremely tight, so I wonder if it's something else. Since youv'e had the machine apart, did you put the spanner nut on really tight? This might cause slippage. It's a good idea to use a spanner wrench to get the nut on tight. It should be extremely tight.
|
|
![jchild40's Avatar](/images/avatars/default_avatar.gif) |
New Member
|
|
Jan 11, 2009, 09:20 AM
|
|
![Quote](custom/vgo/images/misc/quote_icon.png) Originally Posted by ShadyLady
In order to get to the drive block you have to take off the agitator, the spanner nut, and the inner basket. You will then see a somewhat "bell" shaped metal piece that goes over the tube and agitator shaft. Usually the drive block is on extremely tight, so I wonder if it's something else. Since youv'e had the machine apart, did you put the spanner nut on really tight? This might cause slippage. It's a good idea to use a spanner wrench to get the nut on tight. It should be extremely tight.
I started digging into the machine with your suggestion in mind and quickly realized that I haven't gotten into this section of the machine yet (inbetween the brake and the tub). I also realized that I wasn't going to either! It's all pretty tight, and I do not have that wrench.
So, I took the gear case off and started messing with the brake. By hand, I disengaged it and spun the tub checking to see if the drive block was tight. I figure that if by spinning the brake mannually and the tub spins without feeling "loose", then drive block must be tight.
Now I think that I need a bigger & stronger spring in the clutch. I think that it is not strong enough to disengage the brake all the way and just continues to spin. I've emailed some part sites to see if I can get a bigger spring (the clutch came with one, but I must have thrown it away!).
|
|
![ShadyLady's Avatar](/images/avatars/default_avatar.gif) |
Junior Member
|
|
Jan 12, 2009, 01:46 AM
|
|
If you have not had the two baskets apart then it's a sure thing the drive block & spanner nut are on tight. They are qute a tough job to get off!
Do you hear a "clunck" when the machine goes into the spin cycle or when it stops? Or both?
|
|
![jchild40's Avatar](/images/avatars/default_avatar.gif) |
New Member
|
|
Jan 12, 2009, 05:20 AM
|
|
![Quote](custom/vgo/images/misc/quote_icon.png) Originally Posted by ShadyLady
If you have not had the two baskets apart then it's a sure thing the drive block & spanner nut are on tight. They are qute a tough job to get off!
Do you hear a "clunck" when the machine goes into the spin cycle or when it stops? Or both?
No I don't. There is no unusual sounds coming from the machine... that's what leads me to believe it's not the gear case (fingers crossed). That's typical of a bad gear case, right?
|
|
![jchild40's Avatar](/images/avatars/default_avatar.gif) |
New Member
|
|
Jan 18, 2009, 05:28 PM
|
|
Does this machine have multiple gears for the spin cycle? I'm still trying to figure out what's wrong, so I know what to replace.
It seems like it's stuck in a higher gear, and doesn't have the torque to get the spin started. (since if I start it by hand it will take off)
|
|
![ShadyLady's Avatar](/images/avatars/default_avatar.gif) |
Junior Member
|
|
Jan 18, 2009, 05:49 PM
|
|
If you replaced the clutch I suspect the transmission (gear box). Since I'm not there to see the machine I can't give an accurate opinion and I'm not an expert. Sometimes the lid switch causes this problem, and you would have to know how to test it. The local library often has information on fixing appliances.
Perhaps you could re-post your question to get other opinions.
|
|
Question Tools |
Search this Question |
|
|
Add your answer here.
Check out some similar questions!
Whirlpool washer agitates, but won't spin with full load
[ 4 Answers ]
I have a Whirlpool Ultimate Care II Quiet Wash I washing machine, Model #LSB6400LW1. The washer agitates fine, and but will not spin with a medium load WITHOUT my reaching in to the washer and helping it get started (by twisting the inner basket like a roulette wheel).
With a full load (it is a...
Whirlpool front load washer rubber boot
[ 1 Answers ]
Our washer rubber boot is molding and smells. I have read some info on this site and have concluded I'll need to replace it. I can't find the part on any websites. Any suggested locations to purchase this part? Does anyone have a part number and/or name? Also is there any known remedies to get...
Whirlpool model LSC6244AQ0 top load washer
[ 1 Answers ]
This washer is spinning the agitator in the wash cycle and the spin and drain cycles seem fine.there is a part called the clothes mover which seems to spin freely.this clothes mover used to spin in a direction forcing the clothes in a downward motion.it seems to have stopped.the agitator moves...
View more questions
Search
|