Ask Experts Questions for FREE Help !
Ask
    suptclark's Avatar
    suptclark Posts: 64, Reputation: 8
    Junior Member
     
    #1

    Apr 3, 2010, 12:38 PM
    Where can I get a DSC 5010 alarm installer's manual
    I would like to get this manual so I can maintain my system. I am no longer monitored.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #2

    Apr 4, 2010, 10:13 AM

    I don't think I am allowed, Try,
    DSC
    Email or phone them from the contacts list. They may help.
    Likely you need to Disable communications, and Telephone line monitor to clear the trouble light(Failure to communicate).
    I believe the locations are 015, and 380.
    Anything in Particular you want to do?
    Can you get into Programming Mode, *8 CODE should make the 2 led's flash? ## to Exit.
    suptclark's Avatar
    suptclark Posts: 64, Reputation: 8
    Junior Member
     
    #3

    Apr 5, 2010, 06:09 AM

    I need to replace one smoke sensor and want to be clear on procedure. I also plan to replace my two key pads.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #4

    Apr 5, 2010, 07:05 PM

    I can get you through it, Can you get into programming? If not, it will need to be reset to default programming and codes.
    Is the Smoke wireless?
    Since you have FOB's, it may be.
    I will see if I can find a site with the Manual. I have an Account with DSC, but am sure I can't give it out. I can probably give you a site.
    Wireless or Hardwired Smoke?
    suptclark's Avatar
    suptclark Posts: 64, Reputation: 8
    Junior Member
     
    #5

    Apr 5, 2010, 07:22 PM

    I don't know if I can get to programming. System is hard wired.
    Old sensor is 2112/24T replacement is 4wt-b. When the sensor is changed my next job is to replace the keypads
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #6

    Apr 5, 2010, 08:54 PM

    Sorry, I read 2 Keyfobs, you said 2 keypads?
    You will have to assign Keypads after installing, you will need to remove AC and Battery first.
    Try *85010, if you get 2 red lights flashing you are in, press ## to Exit.
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #7

    Apr 6, 2010, 05:33 AM

    Since the detector is hard wired, you just need to remove power, swap out detector, then reset clock, with *6 CODE(Master Code), for system programming, it is *8 CODE(Installer Code).
    suptclark's Avatar
    suptclark Posts: 64, Reputation: 8
    Junior Member
     
    #8

    Apr 7, 2010, 05:13 PM

    I was able to download the manual from a site I found. Hope fully I will be able to get this done. If I do get stuck, I will be talking to my new best friend. Thanks for your input!
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #9

    Apr 7, 2010, 06:44 PM

    That is a Nice Panel, Expandable to 32 zones, wireless contacts and sensors(motions, glass break, smokes, Keyfobs, etc... )
    There is an automation board for lighting and relay control as well as remote arming, disarming, I have a door window transmitter in my vehicle and chimes inside my house if the door in my Van is opened.
    I have the 32 LED Keypad in the bedroom and I can see what zone by the location of the LED.
    I have the Icon Keypad in the Office and can be programmed 4 different chime sounds, My Van is 1 sound, front door is another, Garage, and Shed in the Back is the other 2 chime sounds so you can HEAR where something is happening. Then at the Entry I have the Alpha Keypad, you can give it Custom Names, and has a 128 event log, so you can tell what the last 128 events were(Maid arming and at what time, What zone went into alarm, etc... )
    Can help if you have an Idea. Take Care
    Stratmando's Avatar
    Stratmando Posts: 11,188, Reputation: 508
    Uber Member
     
    #10

    Apr 17, 2010, 06:50 AM

    Here's your User Manual:
    ADT Security System Owner?s Manuals | ADT Security Services

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Programming DSC PC1832 alarm [ 3 Answers ]

HI... How do I change the delay time on a DSC PC1832 STAY-ARM key to 30 seconds delay. Thanks

Dsc alarm pc5010 I stopped monitoring, can I still use alarm? I keep getting a troubl [ 1 Answers ]

I stopped having my dsc alarm PC5010 monitored. Can I use the audible only? I keep getting a trouble, clock problem and it won't let me set it.

Changing installer code on a dsc 1832 alarm system [ 2 Answers ]

How do you change the installer code on a DSC 1832 alarm

Keybus Fault on DSC PC1832 alarm system [ 1 Answers ]

Getting a keybus fault error on DSC PC1832 system. Board problem?


View more questions Search