Ask Experts Questions for FREE Help !
Ask
    mksant's Avatar
    mksant Posts: 22, Reputation: 1
    New Member
     
    #1

    Apr 14, 2009, 04:16 PM
    Where to find an aux spill switch for york diamond 80 furnace
    I have an error code that says the aux spill swich is open, But I think it is just going bad because it works sometimes and may be getting ready to go bad. Where to find an aux spill switch for york diamond 80 furnace?
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #2

    Apr 14, 2009, 04:30 PM

    Never heard of a aux spill switch? Is your unit in the attic?
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #3

    Apr 14, 2009, 04:31 PM
    How many flashs is the fault code?
    mksant's Avatar
    mksant Posts: 22, Reputation: 1
    New Member
     
    #4

    Apr 14, 2009, 04:32 PM
    Four times
    mksant's Avatar
    mksant Posts: 22, Reputation: 1
    New Member
     
    #5

    Apr 14, 2009, 04:33 PM

    Not in the attic but in the wash room next to water heater
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #6

    Apr 14, 2009, 04:33 PM

    If it is in the wash room odds are you need to clean the flame sensor
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #7

    Apr 14, 2009, 04:34 PM
    Laundry deturgant cause a biuld up on it and will not let the flame stay on properly
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #8

    Apr 14, 2009, 04:35 PM
    Four flashs is usually limit switch on york furnaces. Not sure why is says aux spill!!
    mksant's Avatar
    mksant Posts: 22, Reputation: 1
    New Member
     
    #9

    Apr 14, 2009, 04:36 PM
    I have no knowledge on a furnace I found this info on line and got the error codes, where and how do I clean a flame sensor
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #10

    Apr 14, 2009, 04:38 PM

    OK no problem, I will help you threw this.
    First take the top door off your unit
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #11

    Apr 14, 2009, 04:39 PM
    Then locate the burners, on one side will be the ignitor, usually the right. And on the other side will be the flame rod.
    mksant's Avatar
    mksant Posts: 22, Reputation: 1
    New Member
     
    #12

    Apr 14, 2009, 04:39 PM

    Done
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #13

    Apr 14, 2009, 04:40 PM
    http://www.mobilehomerepair.com/medi...-30788-700.jpg
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #14

    Apr 14, 2009, 04:40 PM
    Rub this with a piece of sand paper or steel wool
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #15

    Apr 14, 2009, 04:41 PM
    Have you ever watched the unit to see exactly what is going wrong on it?
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #16

    Apr 14, 2009, 04:43 PM

    Also your fault codes should be on the back of one of the doors, or in your owners manual
    mksant's Avatar
    mksant Posts: 22, Reputation: 1
    New Member
     
    #17

    Apr 14, 2009, 04:45 PM

    THANKS for the info I will try it and reply later!
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #18

    Apr 14, 2009, 04:46 PM

    OK let me know, hope it works for you
    mksant's Avatar
    mksant Posts: 22, Reputation: 1
    New Member
     
    #19

    Apr 14, 2009, 04:47 PM
    Yes, If I turn the unit off and back on after I take the cover off it seem to for fine over night but when I get home in the evening it's back to the same thing. That which is I turn the thermostat up it kicks on and off after a quick cycle and goes off until I take the cover off and restart it again
    Joshdta's Avatar
    Joshdta Posts: 2,549, Reputation: 45
    Ultra Member
     
    #20

    Apr 14, 2009, 04:51 PM

    How is your furnace filter?

Not your question? Ask your question View similar questions

 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

York Diamond 80 blowing cold air. [ 13 Answers ]

Hi All... Hopefully uou can help me out... I have a york diamond 80 gas furnace. It was working fine up until a few days ago.. It began to blow out cold air when the house clearly was not even close to "requested" temp. It turns on, starts the initial motor, the humidifer also kicks...

Error code for "open pressure switch" on York natural gas furnace [ 6 Answers ]

I get three red flashes from the furnace after an attempt sequence when the t-stat calls for heat. The motor starts, and seems to try to light but after about thirty seconds, it quits and gives the error code. I have removed both gray tubes from the pressure switch and made sure they are...

Inducer Motor on York Diamond 90 Keeps Running [ 4 Answers ]

I recently had the inducer motor replaced when it burnt out but I am having issues again. The inducer motor keeps running and won't stop until the whole system shuts down. Let me correct myself. I actually am reading about 26 V on the terminals of the pressure switch. The voltage on the...

Spill or Aux Limit switch [ 9 Answers ]

My York Diamond 80 is not heating. When I turn it on the fan starts but flame does not attempt to ignite. The diagnostic code flashes 4 times. Sheet says 'Aux. Or Spill Limit switch' What are these? Where are they? Can they be reset?

York Diamond 90 [ 1 Answers ]

I have a york diamond 90 and I have 4 code show what could it be


View more questions Search