Ask Experts Questions for FREE Help !
Ask
    wmayo's Avatar
    wmayo Posts: 4, Reputation: 1
    New Member
    		  
    #1

    Feb 7, 2010, 10:53 AM
    Tighten auger belt on 8HP Murray Snow King

    How to tighten auger belt on murray 8 hp snoe king
    crigby's Avatar
    crigby Posts: 4,343, Reputation: 107
    Outdoor Power Equipment Expert
    		  
    #2

    Feb 7, 2010, 11:06 AM

    Hi,
    I broke your post away from the place you put it for the sake of visibility to the membership.
    More information other than given is necessary to accurately answer your question because of design, factory and ownership changes. How about a model number?
    Peace,
    Clarke
    wmayo's Avatar
    wmayo Posts: 4, Reputation: 1
    New Member
    		  
    #3

    Feb 7, 2010, 11:10 AM
    Quote Originally Posted by crigby View Post
    Hi,
    I broke your post away from the place you put it for the sake of visibility to the membership.
    More information other than given is necessary to accurately answer your question because of design, factory and ownership changes. How about a model number?
    Peace,
    Clarke
    Murry snow king snow blower 8 hp. Model 627840500 27"
    wmayo's Avatar
    wmayo Posts: 4, Reputation: 1
    New Member
    		  
    #4

    Feb 7, 2010, 11:27 AM
    I have snow king 8 hp. Mod.62784050 I need to tighten thr auger belt
    Tighten auger belt on murray snow king 8 hpl27" mod 62784050
    crigby's Avatar
    crigby Posts: 4,343, Reputation: 107
    Outdoor Power Equipment Expert
    		  
    #5

    Feb 7, 2010, 12:41 PM

    Hi,
    I am hoping you that you may have typoed as I found a decent parts breakdown, and some terrible ones. On this one refer to items # 103, 110, 148 and 149 on pages 17 and 18. There is a slot in item# 103 that allows you to move the idler inward to apply more tension. See attachment.
    Peace,
    Clarke
    wmayo's Avatar
    wmayo Posts: 4, Reputation: 1
    New Member
    		  
    #6

    Feb 9, 2010, 09:33 AM
    Quote Originally Posted by crigby View Post
    Hi,
    I broke your post away from the place you put it for the sake of visibility to the membership.
    More information other than given is necessary to accurately answer your question because of design, factory and ownership changes. How about a model number?
    Peace,
    Clarke
    Clark Thanks for the cut sheet on my snow king it was most helpful .Great job+++++++
    Wmayo
Not your question? Ask your question View similar questions
 

Question Tools Search this Question
Search this Question:

Advanced Search

Add your answer here.


Check out some similar questions!

Murray Snow Blower Belt Slips Off [ 10 Answers ]

We replaced the drive belt on a Murray 8hp 2 stage snow thrower but it slips off immediately, even when I just pull the starter and rotate the pulley. It's the right belt according to the owner's manual, but it seems perhaps I could get away with a 1" smaller length and still not load the...

Snow blower won't throw snow impeller works auger works new belt pushes up the chute [ 11 Answers ]

The impeller works the auger works put a new belt on the snow starts to come out the chute goes about six inches plugs no broken pin checked all I could

Ultra by murray snow blower belt [ 1 Answers ]

Need the large belt for a G2914050 Ultra by Murray 10HP 29 inch.

Murray Snow Thrower Euro Series how to adjust v-belt [ 1 Answers ]

V-belt for the thrower impeller is slack. How do I adjust this?

View more questions Search