Search:
Type: Posts; User: lexefx
Search:
Search took 0.00 seconds.
-
Hey all,
So I had a fluorescent fixture in a closet stop working, like a starter. It was not serviceable so I replaced it. Same blinking occurred. Jiggled the wiring in the ceiling (to the switch)...
-
How would I get you this diagram? The rogers-white tech guy said there is no turn on wire for this module. I didn't end up with any loose wires, all were transferred over per their diagram/conversion...
-
I decided to mess with this again. Auto fan works with AC, but not with the furnace. Isn't a thermostat in charge during AC only? What controls the fan turn on in auto furnace mode.
-
Furance is a Trane XE70. Original boad went intermitent shut-down. Swapped to 843. Green light running. When it's on auto furnace kicks on, fan does not.In about 90-120 seconds I then ...
-
Hi Dr,
I am not sure these pics may help. Other than water inlet, and water Many solenoids, particularly agitator / spin, are not there. Water level and temp both run through the timer. There...
-
Thanks Dr - That's the one I was using.
-
Dr,
Any idea which guide to use? This behavior reminds me of a starting cap failure (furnace blower motor). Hum, and stinky if left on. It does spin, so the cap sounds unlikley. You sent so much...
-
Will check them out. Thanks for the 411 Dr. T .
-
For the life of me I can't find a plaque or other marking besides these two numbers
8318015 & W10025400
Will fill, drain & spin, but it will not agitate. From Web searchin It sounds like a...
-
Tom,
I know its been ages. Are the hot and cold trim valves universal? I have one leaking, and I am thinking of redoing all 4 (2 faucets). Thanks
-
DG - It was a T20 - your right - Thanks!
-
My clutch housing just free wheels. Troybuilt told me to drop a rope in then plug hole to stop the piston close to
TDC - my problem is my clutch housing just free wheels - its not connected to the...
-
I had a Marathon Cat # X004 in there. I got one shipped in 1 business day with cap for $110 (from R/S Baldor, Leeson, Fincor & Marathon Electric Motors, Sales, Repair & Service 800 279 2267 ask for...
-
Thanks KC13.
How difficult is replacing the blower motor, and new running cap? I am willing to try, pretty comfortable with electricity.
-
I have a Trane XE 70 split unit. 19 years old, current motor and cap are 10 years old. The blower motor stopped working on AC. My AC outdoors runs fine.
Motor issue persists regardless of Tstat...
-
Replaced gas valve under warranty - that fixed it. I also went to flamelocksupport.com and ordered the upgrade, might as well be upgraded!
-
Unit was new about 14 months ago, worked fine till recently.
Whirlpool BFG1F404053NOV0751118163
Valve: Robert Shaw 64-LF8-376R110 RATSP1
Initially I was able to light the pilot again, and fire...
-
All fixed up thanks for your help Tom.
A
-
Very Interesting follow up.
So my pressure tank for my well failed and flooded my basment. When I ordered a new Champion tank - and had it delivered - it was necessary to move my water heater.
...
-
Never thought of this till now, but the precense only in my hot water lines... made me think my waterheater was breaking down. It was 17+ years old -replaced I - I will report back if they clog...
-
Today I removed the cold water supply trim screws from the valve body and flushed from there. Gravel out problem solved. :0)
-
Thanks for working with me Tom.
Its actually a bit different. It's a single handle ball type Circa 1990. It is pressure balanced, and I have replaced the spool - and even soaked it recently in CLR...
-
When I remove the knob for adjusting water temperature, there are 2 holes that supply water to the knob section. Before if I plugged one of them the other would rush, now if I plug cold, hot will...
-
So - I reduced my water heater temp, so this is more bearable. Any ideas on where I should be looking? I am hoping to not have to open the wall, but if you have any idea other than total re-plumb of...
-
Hi
Tom, Glad to hear your getting back to your old self.
We've been rooting for you!
I have repeadley dismantled and flushed my delta single knob.
Tom's sugestion from a few year ago. It...
-
Popatim -
I think you were right about the pump and motor assembly. The issue is now intermittent -
Thanks for the answer.
-
@ 2000 GE potscrubber
It will fill with water, and drain, but it hums like an electrical motor is stuck, and no water pressure is making it to the rotator bar. Is there a pressure pump that may...
-
Tom -
Fully dismanteled both 1600's and with returned wrater pressure a steady small stream pours from both faucets. I tried indiviually pluggung the holes the springs were in with my finger. When...
-
I am so on it - that's very close to what I have. I will do it this afternoon, hopefully on both units / Thanks so much Tom - I'll report back when Its completed.
-
Tom- What I didn't know how to do was flush them. The spool had the acess to flush - the only other thing I have for flow adjsutment is trims on both hot and cold. The cartridge is about 1 inch...
-
My home is 16 years old, I've had it for 5 years.
I am on a pump - with 70LBS high cutoff and 55lbs Low turn on. All copper -
I have 2 Delta 1600 shower faucets - one tub spicket with shower...
|