Search:

Ta,

Regarding your comment "adding a recessed light to a shower"... you need to review the below listed NEC CODE before doing anything in to your shower area. Also, You are aware that because you...

Is this the receiver that you disassembled? If so, the best thing to do is:

1) Purchase a new one

Or

2) Take the complete assembly to a local TV or electronics repiar shop in your area and...

Hey... tks for updating us... post the pics of the panel back plane and the compressor (the control box/stater, whip and disconnect) and a general pic of the location with respect to the panel.
...

Does your compressor have the control box mounted on its side? Is the whip from the control box still attached to the disconnect switch? Or is the disconnect switch missing and your plan to replace...

So if I understand correctly you have 3P to you panel... as told by the prev owner.

Just to make sure... you need to first verify that the pnl you are attempting to connect to is in fact 3 Phase....

Ok... you hadn't mention the switch before that's why I asked about a pull chain.

Also, I asked before:

What model number do you have? Most fan manufactures instruct you to set the fan pull...

Best of Luck!

The black&white combo wire should be hot toand from the switch. Reconnected to the hot wire entering the ceiling box,, to the white wire going to the switch, This white conductor shoud be marked with...

Think about what you just said! If in the ceiling box the wiring config is BLACK-BLACK, WHITE-WHITE, then when he operated the switch he would have a dead short. BLACK HOT in wired to BLACK HOT to...

AdviceSeeker,

Just follow this guide... any question just re-post.

1) Was the original fixture on a 3way switch in a kitchen?

2) In the ceiling box... did you have a single black(HOT),...

Please provide fan model #, Remote model # and are you saying that you don't have a pull chain on the fan or a wall switch controlling this fan? Where is this located? If it's a fan problem... locate...

Is this a Kendal remote or an after market universal remote? It would help if you provided the model # of the remote and fan...

Joe

How is that vague link going to help or even answer the OP's specific question?

No pull chains on the fan? What model number do you have? Most fan manufactures instruct you to set the fan pull chain to the high position and control the speed/on-off via the remote.

Litex...

Before purchasing anything... you need to verify that the receive located in the canopy of the fan is still functioning. Drop the canopy disconnect the black lead going to the receiver(Hot wire) then...

Try this link... but you might need to find a US based distributor.

::Product Information::HUI YANG ZING EAR INDUSTRY CO.,LTD.

Joe

FYI:

It's actually called a "dusk to dawn" or "photo" sensor

Ryan19,

What you said about the breaker box makes no sense.

Is this a MWBC with a Red wire on one breaker pole and a black from the same cable on another breaker? Or is the "breaker box" with...

What brand/model comp?
Is this a comm/ind application or home/garage/workshop?
Is the branch ckt and disc already in place? If not, how far is the run?
What panel type is feeding the branch ckt?...

Donf,

Stop miss quoting the NEC!!

Where do you see the phrase "limits the length of the connecting cord to 25' for a side connection to an RV. And 30' to a rear connecting point."??
...

tsboring,

A camper needing 120V / 30A @ 180' using UF 10/2... for a temp feeder, tells me you never pulled a permit nor had any work inspected.

Your local AHJ would have never approved this...

Remove the top of the tank and flush the tank completely. As the water fills... and the chatter starts... place your finger lightly on the top of the fill valve... if you feel the chatter put a...

Quiet,

Regarding your post... I have 3) questions:

1) What sort of fan / light operation would you like?

2) Have you considered installing a combo ceiling fan/light remote?

3) Is power...

Impossible..?

A TC-P42U2 is a 42 inch, 1080p Plasma TV... sounds like someone swiped a magnet across your screen... unless you're willing to replace the screen for big bucks... I'd dump it and get a new LED model....

Madzalover,

Please checkout this NYC Electrical Code Reference:

http://www.nyc.gov/html/dob/downloads/pdf/ll39of2011_electrical_code.pdf


Please see page 44, ARTICLE 334...

Scott,

Are you an EC in NYC or else where?

Just wondering why you are not keeping up with code requirements in your trade and giving wrong advice.

Sites like this can be helpful but it's the...

NYC approved the use of Romex back around 2008.

As long as the term "house" refers to a wood frame structure you should be OK. If this was a high rise condo or apt building the use of Romex might...

Was a permit pulled for existing "little room"?

I bet not... and that might also enter into his problem. Maybe he thinking about selling and he's discovered that the code... ees will find it or a...

The chances of you getting an approval is slim... in most cases an attic build out is difficult at best. You need to check with your twp building dept to see what is possible. Once you start talking...

My M40 just turned 47 yrs old and with the exception of the wooden stock which has been changed around 4 or 5 times, the addition of state of the art optics/range finder... it's as deadly today as it...

Depending on the age of your existing system, where you live and if you're system is Central Air Only or Central Air/Heat... it has to correctly size as to SEER rating for your needs. If for example...

Running a earth ground is not a good idea esp if you do not follow the code and run that ground back to your panel and also have it bonded.

If the wiring has no ground and you need one......

If you are measuring Volts at the 2nd 3Way... you should be measuring it on either the Traveler or Switched terminals(Red or Back wires across from each other). If you're measuring the voltage across...

You have a 3 way switch... at the lower switch in the hall... remove the faceplate of the switch and pull the switch from the box. Verify that the N pigtail is tight... then note the wire colors on...

jman2012,

Is the Feeder between the Main Pnl and the Sub-Pnl overhead? If not overhead, is it direct buried or in conduit? It might just be a defective N between the Main and Sub. Stranded cable...