Search:
Type: Posts; User: adkhkr
Search:
Search took 0.00 seconds.
-
Slow but steady lol
Working my way towards tackling the fernco fitting that needs to go.https://uploads.tapatalk-cdn.com/20191207/7b67e52d6ad2e133f59fc3fd885e7c0d.jpg
Sent from my SM-N975U1...
-
For the toilet plumbing, does this look right?
4x3 closet bend to 3x3x2, with the 2in vent going up the wallhttps://uploads.tapatalk-cdn.com/20191206/dc19111dd5e1f3f14415c4ea8feab60e.jpg
Sent...
-
Except for the rest of the pex supply lines, this wall is done. This was a tough one. https://uploads.tapatalk-cdn.com/20191201/972a85138f4edaf3b5315b72199c3fbd.jpg
Sent from my SM-N975U1 using...
-
Got sidetracked this week but here is the sinks completed less the venting...I'll message you, thanks!https://uploads.tapatalk-cdn.com/20191124/0c94d1628e360588f67bc55edc3e5fd5.jpg
Sent from my...
-
Managed to find the fittings online...had some issues getting the straight section in hence the 2 couplings. https://uploads.tapatalk-cdn.com/20191113/088808cc3d94def659e3edf57d842713.jpg
Sent...
-
This should work, just have to turn it 90 into the wall from the wye. Have to hack the stud to get it in there but it should work. How does it...
-
I can squeeze in the double wye 2inch and put in a 2 to 1.5 bushing for the stub outs. Here is the layout, does this look good? The blue is the 3 inch, the red from the side is the 2 inch vent. I...
-
Got the vent for the sink and shower in coming around the corner. Does this look good? Where the 1.5/1.5 inch pipe transition to the 2 inch, is the fitting I used correct? And I used a vent elbow,...
-
See attached...doing the drains back to back isn't going to work. With that said, what option do I have given the separation between each sink? Would a 2" circuit vent like the one in the pic be...
-
I had my sink layout wrong.. the attached picture is the correct layout.
1. Can the red drain line be 1.5"?
2. How to the vents go with this...
-
Finally getting back on the project.
In this photo...I have the following questions.
In red...are those Wye fittings?
In green...is 1.5" sufficient for the drain lines?
In Blue...is 1.5"...
-
Here is a revised layout... Any more suggestions? https://uploads.tapatalk-cdn.com/20190819/0ecbe46c11734951844e64820d5a2d2e.jpg
Sent from my SM-N960U1 using Tapatalk
-
This is what I had in mind where the 4 inch pipe splits.... And than cap the top of the pipehttps://uploads.tapatalk-cdn.com/20190711/66fa5d1d516b496199a96b6c4d255664.jpg
Sent from my SM-N960U1...
-
Thanks for the input... Here is a revised sketch based on your comments.
Any better? https://uploads.tapatalk-cdn.com/20190709/9c62f7fdf2d662e0674091791331f25d.jpg
Sent from my SM-N960U1 using...
-
Hi -
I am doing a Master Bath renovation and changing the plumbing locations. Also, in the future I will be redoing my kitchen and eliminating a wall where the main waste line runs so basically,...
-
Hey Mark -
Yep... gonna cut out the old shutoffs and do exactly as you wrote. I needed that to convince me. Not worth a flood having to rig it to work. Thanks for you help.
Brad
-
I have relocated my washing machine upstairs on the 2nd floor in an existing bathroom. I had a double sink/vanity that I replaced with a single sink to get the washing machine adjacent to it. I...
-
Does the NEC permit water pipes to be routed above an electrical panel? I would be running Pex water pipes above it. I am limited to where I can put the subpanel and water pipes.
-
I am wiring my basement and am installing a porch light out of the walk-out basement door. At the door I was going to have switches for the lights in the room and the porch light. Can the interior...
-
It is 3c#4 copper wire sized for a 70 amp breaker. It is encased in a grey plastic jacket. Does that describe it well?
-
I am relocating a subpanel to a new location and the existing #4 wire is too short by a few feet. I would rather splice a new piece of wire to it an extend the wire than replace the whole cable as...
-
Here is a quick and dirty sketch of what I am intending on doing... does this look good or would you vent it differently?
The arrow indicates where it will penetrate the floor and go into the 1st...
-
When I run the 2" vent pipe, is it OK to use the short radius 90s? Is there a limit to how many 90s I can use when installing the vent pipe?
There are a few tight 90s I need to install to get it...
-
Going the route of a regular vent through the roof. Should I use 2" PVC for the whole vent, including through the roof?
-
Are you better off going with a regular vent? Should AAVs be avoided if possible? This horizontal vent pipe will be installed in a 2x4 wall so the smaller the pipe the better. Will a 2.5" pipe fit...
-
Looks like I might have a problem with this... the overall developed length would be approximately 50', with 30' being horizontal.
Could I get away with installing an air admittance valve as the...
-
Its been awhile, but I am finally looking to finish this project up. I am going to run the vent pipe to an existing vent... see attached. My question is... is it OK to run an existing vent pipe...
-
Ok... so I can use a plastic box with the metal clip to screw into the face to the steel stud?
I wasn't sure if you had to use metal boxes with steel studs.
-
I am in the process of finishing my basement with steel studs and am almost ready to work on the electric. What kind of boxes do you use when working with steel studs?
-
Right now my heat is connected to an older thermostat. When I had my Central Air installed I never combined thermostats. Now my heat thermostat is on the fritz and I would like to use the WR...
-
Down to my last couple of fittings under the slab and I ran into a bit of a problem. One of the fittings doesn't want to weld. After I weld it, with a little bit of force it pulls apart. I tried...
-
For the length of 4" pipe that connects to the toilet, I had to stake it into position because the natural position was shifted a bit from where I wanted it.
I didn't force it to the point where...
-
Thanks. Two additional questions:
1) Coming up for the toilet, should I use a standard 4" 90 degree elbow and glue a piece of 4" PVC so it sticks out of what will be the top of the slab?
2) On...
-
I have all the concrete trenches done, but now I am confused about how to get the 2" shower pipe to come up in the exact spot where the shower drain is. I bought the shower pan, an americh 38x38...
-
When you say to roll the 4x2 wye above center, is this what you mean?
http://i651.photobucket.com/albums/uu240/adkhkr/Drain.jpg
I have to say, I can't wait until I don't have to break up...
-
Mark... the layout I had isn't going to work because my measurements were incorrect. Measure twice, cut once right. Sorry you made the layout for nothing, my apologies.
Anyway... unfortunately...
-
Mark -
I have only installed one 10' piece of 4" PVC just past the 2-Street 45s. I haven't done anything in the bathroom or kitchen. Any help would be great.
-
So do you piece it together so it covers around the whole pipe?
Just so you understand what I am talking about, I want to wrap the 4" and 2" pipes.
I am moving along with the plumbing. The...
-
Yes... the bathroom and kitchen are in the basement. Well if they are groundless than I'm glad to hear it. I will get this section of pipe in, backfill, fill in the concrete and than work on the...
-
Speedball... to clarify this is where the problem is. There is nothing from upstairs coming into the pipe at this point.
http://i651.photobucket.com/albums/uu240/adkhkr/PLBG-1rev.jpg
-
OK... so I'm still moving on the project and I got everything done in the picture with one problem. When I connected the 2 45's making the right hand turn I made the angle a little too steep. When...
-
Wow, thanks for the great advice. I might actually be able to do this by myself with the help from you guys.
For the cleanout, is this what you are talking about? This would be in the vertical...
-
OK, I think I'm understanding it now. I made a new sketch of the layout. How is this?
http://i651.photobucket.com/albums/uu240/adkhkr/PLBG.jpg
-
I'm a little confused... should I come off the main with a 4x2 Wye to the floor drain -than- 4x4 wye to the bathroom/kitchen -than- sanitary tee up for the upstairs laundry.
Should I not use a...
-
I am not sure if this changes anything but this plumbing will only be for the basement. I might also include upstairs laundry later on though. Everything else from upstairs is tied into the...
-
Thanks Tom for the help. So now that I have the initial work done on the plumbing, I have to get started with the rough-in plumbing. Attached is a picture of the next phase of the project. After...
-
So would a sanitary Tee work for the vent?
-
-
Here is a picture of what is required...
http://i651.photobucket.com/albums/uu240/adkhkr/septic.jpg
-
So I have installed the PVC under the footing and connected the main house trap that I built with PVC fittings. My next question is what type of fitting the main fresh air inlet should be?
I was...
|