Search:

E1 error indicates a bad thermister

Got to servicematters.com Use the technicial library, tech sheets. Put in your model# for a list of codes and what the fix is.

Pull back the rubber boot inside the front and clean it out. Water sometimes sits there and causes mildew oder. Using a small amount to clean will help

Have you removed the vent hose and checked/cleaned out the vent to the outside? Sometimes small animals/rodents can get inside and make a nest.

What brand are the appliances, and how old are they?

Can you describe the noise?

I recently went through a similar situation. Yes it is difficult, but you need to focus on you. This is someone that will always remain in your heart and soul. Remember the good times, and treasure...

Could most likely be the magnetron going out. If it is, check your owners manual, as some have a 5 year warranty. That will significantly reduce the cost.

Changing the belt is really not a difficult or expensive job. Go to your nearest Sears parts place. They will usually have the belt, and can give you a breakdown diagram on how to do it yourself.

Are you using fresh gas?

Extended warranties used to be a waste of money. Now that the manufacturer has made every model with at standard 1 year on everything, it can become costly to replace appliances, when the extended...

Go to sears.com, put in the model# and you can print the owners manual online

The simple inexpensive recipe is on the back of the Frenchs Onion Ring can. Turns out the best

Your problem is with the timer. When it goes to a spin cycle, there is an automatic 7 second pause allowing the gearcase to ch. You are actually manually creating that pause when you open and close...

The only way is to tilt the machine back and take the pump out from underneath. Use a 2x4 to hold up the machine. Also be careful, as when you take out the pump there will be water in it. You will be...

Get a stop watch and actually time how long the flame stays on. Then disconncect the vent hose and time it again. If it stays on longer with the vent disconnected, then you have a restricted vent. A...

If you bought it used, there is no warranty

This sounds like a Calypso washer. If that is the case, appraently something was washed that came apart. There is something stuck in the pump. That will cause the LD error. And then if the water...

There is something caught in the pump.

What brand is your dryer, and how old is it?

California is an at will state. Your employment can be terminated at anytime without reason. The only exception would be any violation of the civil rights act.

Sounds like clutch/basketdrive problem (brake on the machine). If you are mechanical you can do it yourself. Having it done by Sears is about 180.00. Much cheaper than a new one.

The most common problem is the push to start switch has shorted out. Try replacing that first. It is a rather inexpensive part and is available at most Sears repair centers.

If your dryer is designed for a side venting, there will be a small "knock out" panel on the bottome side of the machine. Not all machines are capable of being side vented.

There is an event at your local sears today 12/30... You can ask a technician for free. It is going on from 10-6. take advantage

I do believe Sears had repair technicians in Canada.

Depending on how much oil you are seeing, but the transmission is the main part, so it is like running your car with an oil leak. Also the oil can mix with the water and stain your clothes

Sounds like a transmission problem. One way to check for sure is to see if when the water starts to drain out, does is start to spin when there is still water inside? That is call no neutral drain....

Sounds like could be the motor. Check the connections. Also check all the connections to the timer, one may be loose

More likely thermal fuse or thermostat. Possibly restricted vent hose

Check vent hose for restriction. Remove the hose and see if dryer heats up without it. If not, then check thermal fuse or thermostat.

If the washer is in the garage, you can take the drain hose and lower to the ground, creating syphoning condition. The problem is probably the pump. Either it is split, or something is stuck in it....

Recommended size for your sq ft would be a 4-5 ton unit

Before you invest the money, check your vent. A restricted vent can cause the no/limited heat. Average repair from sears is minimum labor of 132.00 plus the cost of parts.