Search:
Type: Posts; User: huskyjjc
Search:
Search took 0.00 seconds.
-
You could have a bad batt. New or not. But if alternator is not charging that needs to be looked at
-
Look at the firewall of the truck and find the two hoses that go into it they will norm be on the left. After the truck is warm touch both hoses and see if they are hot if one is hot and other is not...
-
You will want to check the wiper linkage to see if anything is worn and check where the wiper arm connects to the linkage to see if its all tight
-
Is the alternator charging the batt? If there is not a good 12v source at all times the ecm can go a little crazy
-
If all fuses and batt are good check the wires at the starter sometimes there are wires at the starter motor that go inside the car. They will be on the same post as the batt cable
-
Does the 3rd stop light work? If the 3rd stoplight is on but the reg. stop lights are not it can be a bulb but not the switch. If all fails the next thing to check is the turn signal switch as the...
-
Check the injectors make sure they are not leaking
-
In the past I have come across a bad crankshaft sensor that will sometimes work or not.
It should set a code that will say no crank signal . If you know how it can be a easy fix and you can buy one...
-
You may want to check for power at the starter first and check the wire coming from the ing. Switch. If you want the old school way of checking have a friend try and start the car and you tap the...
-
The normal thread is left hand but I have seen right, as far as breaking it loose spray it with penatrateing fluid and you will need if you don't have one a fan clutch tool . The tool has two pieces...
-
It sounds like a starter, but I have had many problems with a bad connection at the starter check the batt cable at the starter first
-
If there is no air you might have a bad head gasket, the compression from the cyl can push air in the coolant and force it out
-
Well it's a little odd for the ck engine light to go on after changing a batt cable , but if so you will need to hook up a scan tool to clear the codes
-
If you where in the jersey ares I would look at it . At far as finding someone go to a radio shop ,someone who does only that because they will find the problem fast
-
Give me a little more info like what is it hooked to and how
-
I can give you step by step but it's a easier for me to fax
-
I have alldata it has all schematics if you tell me a fax # I can help
-
The knocking noise could be a few things first I would say a rod knock. The rod is at the bottom of the engine and is connected to the crankshaft with a bearing. If the bearing wears out it will...
-
You can try to change the starter solinoid its cheap. Allso did you check with a test light to see what has power and what did not. All the power goes from the batt to the sol. And to the inside of...
-
The throw out would make noise all the time until you step on the clutch. But how good is the clutch? If its worn it could do this. But I say the sinkrow is bad that's what puts the gears inline so...
-
Check the ign. Switch go to the switch make sure there is power going in . The norm is a red wire or yellow and thick. If there is power going in try to cranl the engine and check to see if there is...
-
You can try to trace the wire to see where it goes and to what. If it is not grounding out the buy a new link and bypass the old one by cuting out the old link adding the new one and conect it to...
-
OK this may sound strange but I had this happen in my shop. I was never able to find out why it worked but it did . First make sure spark and fuel are good. If so buy carb cleaner and spray half the...
-
If you put power to the comp. will it work? If so then you have a bad wire. If not check the high side switch
-
Did you check any fuses? Or the main cable to the starter give some more info on the problem
-
You may want to check the wires at the back of the alt. make sure the regulater wires are not grounding out . If they ground out that will send the alt. to full
-
Your lockup in the trans is bad the lockup is what puts the trans in o/d and when you come to a stop the trans will go back to 1st gear but when the lockup is bad the trans will stay in o/d and the...
-
Sometimes scan tools don't work I have a snap-on and a otc and sometimes one will work and the other won't it just the programs in the scan tool and the car programs not working together as far as...
-
If the cable is one piece from the speed-o to the trans it should go to the trans gear and that should come out by unbolting it from the trans
-
You may want to check the speed-o gear in the trans . There are two one that rides on the rear shaft of the trans and one that the cable screws to
-
The most common thing I see is the camshaft interupter broken . The interupter is a small magnet on the cam gear that the timing chain drives ,when the magnet breaks there is no cam signal the timing...
-
How about door number 2, this pipe looks like it will break you see the house is only 36 yrs old but it was not made all that well and things seem to fall apart when you fix something . I have...
-
-
Thanks speedball I will give it a try but can you tell me how to get the lead bend out of the cast ( the main waste pipe in the house) with out breaking the cast pipe or breaking my a**
-
My master bath had a leak at the toilet so I pulled the toilet up and found that the closet flange and the lead bend where no good. The lead pipe is so bent and you can allmost put your finger threw...
|