Search:
Type: Posts; User: Majoria
Search:
Search took 0.00 seconds.
-
There is no hole in the lower portion of the bowl. I know the one you're referring to but there is not one on this model.
I adjusted the water level as best I can, the donut can only go up so...
-
Really, I stumped everyone with this one? :)
-
I have a house that was build in 1984 in Worcester, MA and I’m on city water & sewer. I bought it in December, 2002.
I don’t see any brand or model numbers for the toilet itself but there are...
-
What year is the truck?
If the engine is running but just no reaction from the accelerator then you could have a problem with the reference voltage (vref). This engine has three separate vref...
-
Sorry this8384, but disconnecting a battery does reset the KAM (keep alive memory) on this vehicle, I've done it countless times and verified it with a scan tool that the learned values were reset...
-
There is no mechanical linkage between the accelerator pedal and the throttle control so there may be a short in the reference voltage from the APP (accelerator pedal position) sensor. If that's the...
-
It's a known issue, common codes are P2106 and P2135, sometimes P2105 or something else. Ford has a TSB (technical service bulletin) for the P2106 and P2135 codes which involve the wrench light and...
-
Been there, done that, and it is very likely that the root cause is internal transmission. Sorry to give you the bad news but most of the scenarios that you are describing are internal transmission....
-
There's something missing here.
P0420 and P0430 are determined by the downstream O2 sensors which determine the effectiveness of the converters. The first thing a technician will look at is the...
-
Ford offered two bi-fuel options for this eninge in this vehicle, LPG (liquid propane gas) or CNG (compressed natural gas). The engine could run on two different fuels, gasolone and also either LPG...
-
COP = Coil On Plug. Instead of having a coil pack as with older distributorless ignition systems, this engine has the newer common approach of an individual coil right on top of each spark plug thus...
-
Anything that could compromise the emissions will cause the light to come on but only a misfire DTC will cause it to flash.
-
The only thing that makes the check engine light flash is a class A cylinder misfire so first thing is to check it for codes and find out which cylinder(s) are at fault.
If it's cylinder 4...
-
Thanks again. My experience is in automotive hence even something this basic in AC wiring to me warrants a second opinion and clarification. I was really struggling about grounding a plastic wall...
-
Ok, I hooked the two black wires to the two wires on the new thermostat, left the white wire connected to the old thermostat which was touching nothing, ground wire also touching nothing. I turned...
-
The bare wire was installed onto the metal backing of the old thermostat with a self tapping screw. I removed it to pull out the backing plate far enough to take the above photo.
The box in the...
-
Disconnecting the battery would clear the adaptive strategy and erase any codes that were stored.
Another possibility is the MAF sensor which is located in the air inlet tube. Disconnect it's...
-
The only sensors that are used for boost purposes are the MAP and the EBP. Did he show you where the sensor was located?
As far as the incorrect oil, he may be under the false impression that...
-
The main difference is sulfur content. ULSD (Ultra Low Sulfur Diesel) is the current fuel being sold and is rated at a maximum of 15 ppm (parts per million). This fuel is mandatory for 2007 and...
-
Just to make sure I understand, do you need the diagram to remove the door panel or the electrical diagram of the window switch? I don't think I have a diagram of the door panel but I can check on...
-
Thanks.
But back to original question: how do I wire it? It appears the two wires from the new thremostat go to the two black wires on the old on as if to control the current, but what about the...
-
juggallojed - The white wire is connected to two other white wires in the wall, a total of three come together as one that contacts the original thermostat. Power is off.
hvac1000 - I checked for...
-
There is no code 15 but there was a popular code 51 for the internal fuse being blown and the short to ground no longer being present. If the short to ground returns the code will change to 13 (air...
-
Ok, this is similar yet different to a previous topic. I'm trying to install the Honeywell RLV430 to replace an older dial thermostat.
The original thermostat has 2 black wires, one white, and a...
-
Ok, I'm in a similar yet different scenario than the original issue. I'm trying to install the Honeywell RLV430 to replace an older dial thermostat.
The original thermostat has 2 black wires, one...
|