Search:

Yes water running down the inside of the wall. Yesterday I pulled the face plate and on the backside you can see where the water builds up and then eventually makes it way threw the escutchen. So,...

Thanks CM. I am quickly getting that impression about american standard. I also have a handheld in the shower and I had to replace the mixing valve because it wouldn't stop dripping. At least the...

Guy's I have a new tub/shower. I noticed a leak coming threw last week. After a lot (and I do mean lot) I have narrowed the leak down to the face plate on the mixing valve. A single handle American...

I have checked with a few other people and they seem to think it could be the actuator underneath but the machine should be re calibrated after replacing it. Has anyone ever calibrated this machine ?...

I have a whirlpool washer WTW4850XQ. It will not drain after a regular wash cycle, but if I put it into rinse and drain it spins and empties out fine. Pulled apart the drain pump and checked drain...

As always thanks for the input. I will let you know how I resolve this. Probably the 3 port, but that will be after the wives input of course.

First Mark and Tom Thanks for the help with the vanity(and everyone else of course)Everything is in and running great, BUT now I have another question. The tub is in but I have not duro-rocked this...

Thanks Mark. That works great. Thanks for your time. Thanks to everyone.
Shulta

Much appreciated Mark. Tom Thanks.
Shulta44

So on the wet vent, the 2" pipe going to the roof for venting between the tub and sinks is not good enough. I should come off the top of the sink drains and tie back into the 2" vent pipe again....

Not sure if this picture helps. I am no artist. Sorry. shulta44

Thanks Tom and Mark( and everyone else). Mark sorry for the incorrect terminology and yes it will be a wet vent. As far as the toilet I was trying to center it on the wall, but I am going to leave...

Sorry guys should had provided more info. Off my 3" waste line for the toilet, I am teeing off to the other side of the room with a 2" pipe.The T is 4' from the toilet. Once to the other side (6')I...

I am moving a vanity and installing a double vanity. I have access from the basement, so can I come straight up into the vanity with the drain and water supply or should I still come up inside the...

There are 3 small tabs on the top and on the bottom. Star in a corner and lightly press downward. Once you get a corner started run your putty knife along the edges. There is two way tape there. That...

Parents are still using it right now. Kitchen is going to be done the 2nd week of June. After that you can have whatever you want off it.

I had my boiler serviced at the end of the year. I have this done every year from the same company. The guy came Friday morning for the service. He cleaned and tuned it and I paid him. On Saturday...

I am using turbo tax and not sure if I am doing this right. The award type is RSU and the 1099 says 127 under quantity, but when I add the 3 lots together from e trade I get 156. My etrade statement...

Front load? Top load? Are they on storage cabinets? Model number?

So after fiddling around I can answer myself and hopefully it will help someone else. I used a putty knife that I put teflon tape on(to prevent scratching the stainless steel) There are 3 tabs on the...

I have a GE profile PSC23SGRBSS side by side with the water and ice dispenser on the door. The door for the ice dispenser does not shut after dispensing the ice. You have to remember to reach up and...

If the freezer is warm, it is only a matter of time before the fresh food compartment warms up. It draws the cold air from the freezer. Is the freezer frozen solid? What is the model?

Can an existing coin chute (set at 1.50) be adjusted to accept $2.00. If so how? It is a whirlpool dryer CEM2650KQ3
Thanks
shulta44

OK I have a stainless steel Westinghouse cooktop. Model #PL-9 Style Q26707. I figure this thing was built in the early 1950's, but it still works great except for one burner. I just want to find a...

Does the air handler have a additional heating coil(electric)? A heat pump alone will typically not be enough to heat a house or condo when temps get down to the teens.

Is the door sealing tight all the way around? Slide a dollar bill between the gasket in several spots and try to pull it out. There should be pretty good drag. If it is real loose you may need a new...

My shower mixing valve was fine when installed, but now I can't seem to get enough hot water.(rest of the house is fine) When I turn the valve all the way to hot it will get a little hotter but then...

I assume this is a top load washer? If so it is not that difficult, but you will need to purchase a spanner wrench. You will use this to remove the spanner nut, a reverse thread. Do not be afraid to...

Water on the floor could be from a cracked drip pan or rusted out drip pan under the frig. Pull out the frig and check the pan first. Sounds like the defrost water is just running onto the floor.

I have the same problem, I do not want to just pull on the stainless cover for fear of breaking it or warping it. I have tried a putty knife under the face plate but no luck. If you hear anything or...

Is the freezer temp good? Is the freezer frozen up? Has it been defrosted and the problem still occurs? Model #? I would start by manually defrosting for a few hours and plug back in see if the fresh...

Check that you have continuity on the solenoid valves. Valves either not opening or they are clogged. Do not try to clean, just replace the valve assembly.

Could be the overload or relay on compressor. Have a model #

Does your dishwasher have a food grinder? Sometimes these clogg or completely fail and it will really affect the washability.

If the compressor was not running, it would not frost at all.condensor fan runs when the compressor runs. You should here the evaporator fan running in the freezer compartment? This is what will...

Cannot find any amana bc121vw sure this is correct

By turning the timer you put the fridge into defrost. The fan stops and the compressor stops, until the defrost runs for about 20 minutes. Is the evaporator fan running in the freezer when the...

How long did u unplug? Are the fans running? Have you ever vacumed the condenser coils? Make and model?

Fairly easy, but you will need to purchase a spanner wrench. If you pull the cap on the agitator, there is a nut. Unscrew the nut and remove the agitaor auger (do not remove the agitator cam inside.)...

Put a dollar bill between seal and try to pull out. Do this every 10 to 12 inches, it should not pull out real easy. If it does, replace the seal. How old is freezer?

Have you ever vacumed out the condenser coils? Make and Model? Could be overload and relay on compressor itself.

Glad it helped.

I would personaly never clean a water inlet valve, especially if you have hard water.I would replace it. It is inexpensive and not hard to change. 90 seconds is right on. So somehow you have a...

May sound silly, but have you sat and listened to how long the water runs(filling) during the first cycle. Typically a dishwasher fills for a set amount of time. It does not have a pressure switch to...

Thanks Cali and Ex, both valid points. I will check the turbo tax link. Your not joking about the sweet years I see it every month.
Thanks

I have a daughter starting college this year. I have less than 5 years left on my 15 year motgage, a total of less than $90,000 at 4.79%. Rates are at 3.95%(or less) and I can get no closing fees or...

If it isn't getting water it sounds like a solenoid problem on your water valve. It is where your water tube hooks up to the fridge. Turn off the water unhook and make sure you have water to that...

They actually should be warm. The condenser coils are built into the walls of the chest. When is the last time you defrosted it? Should be done once or twice a year. Is the freezer cold and no frost...

Sorry just saw this. Basically the white red and black will all connect to the same terminals as the 3 prong. The difference is you remove the jumper under the neutral(white) that goes to chasis...

See how the right parts work. Good Luck.