Search:

Thanks Milo... appreciate your advice.

I wanted to get in the attic to make sure I was giving you accurate info.

Here is the layout. All pipe sizes are outer dimensions.

Thanks for the reply.

I have 4 vents coming out backside of my roof ( span of approx 25' )


I plan to put metal roof and would like to combine the vents in attic
and just have one vent through roof.


Three vents...

UPDATE : I did not get a chance to talk to mechanic to find out the code given.

They changed the "Auto Shutdown Relay".

Part $20... Diagnostic Test $75.

I've used it every day since the...

UPDATE :
Changed TPS last Tuesday. Truck ran fine Tue & Wed.
Thu afternoon would not start (turn fine but not start)


Used another vehicle and came back about 2 hours later and it started as...

The "check engine" light was not on before or after I changed the TPS.

I decided to change the TPS based on many reviews of Dodge pick-ups with
the same problem.

I will keep your fuel pump...

Got it... pull out red clip and push down on tab.

Off to find throttle position sensor.

Thanks for the reply smoothy, may have to bring it in, but...

Did some searching and many say it's a throttle sensor problem.
Does not seem very hard to replace.

Trouble I'm having now is...

2002 Dodge Ram v6 stalled at red light.

Tried staring 2x... it would turn but not start.

I was lucky, early morning, hardly no traffic.
Pushed it to the side.

Opened hood... not sure why,...

Thanks parttime... I may have to try your suggestion.


aha .... thanks for the link, that's what I was searching for.

@cdad... that's close.

Those would not allow me to embed pass that middle transition section.

The bolts in the picture have a head on end of bolt section that you can tighten from.

Thanks...

No, it would not be used for concrete, I would use in wood.

Need a lag screw on one end and bolt thread on the other, but I need that hex section on end to screw it all the way down to the bolt...

Thanks for the reply... but I've looked local and cannot find, that's why I'm searching internet.

In my area... True Value Hardware has everything I normally need, they do not have it.

I found a picture of the bolts I need on the internet, but cannot find where to get them or the name.


Anyone know what they are called and where I could get some ?

Searched YouTube and found a part in the carb I had not cleaned.
It was hidden inside a cylinder and had to use a small head screwdriver to get it out.

It was clogged... had it sit in apple cider...

Forgot to mention, oil level is full.

It was run approx 6 months ago. It will not start today.


Honda GX390 13 HP generator motor.

Fuel line is clear.


Removed carb and cleaned bowl which was pretty gummy.
Raised float and...

Thanks for the reply joypuly... but do not understand,

Or does that mean the answer is "no" no need for vapor barrier between metal and wood ?

I'm putting a metal roof over a shingled roof.

I will run 1 x 4 pine screwed to rafters... then the metal will screw to 1 x 4.

My question :
Should I put a vapor barrier between the 1 x 4 pine...

Hah... shot in the dark suggestion fixed it. Thanks JB

Home

Not sure what's going on JB... it does not work that way on my computer.

Does not matter which radio button is selected, it brings all songs in.
...

JB... thanks for the file.

Not working as I expected though. It seems to bring all songs in and filters/sorts.

Only wanted to bring songs that match the key code put in D3 by the radio button...

I do have Access... looked at it once and was rather confused.
Much rather excel but may have to give it another look.

Thanks for the reply.

Excel 2003
Workbook with sheets "Search, A, B, C, etc (through alphabet)
Sheets a, b, c, etc have a song name in col A, and a letter code in col B.


Clicking on "search" sheet opens a userform...

Thanks JB... that works great.

... a picture would be helpful... for others to be helpful.

Also size of basement.

Got it with the use of helper columns.

Used MOD function to separate the whole number.
Used MIN function to find the lowest.
Then conditional format to highlight.

If someone has a solution...

I would like to highlight it.

2.45
3.75
2.08
4.06


Need formula that would choose 4.06 from above list.
Even though it is the largest number, the .06 is closest to the whole number.

I'm not following exactly what you plan on doing, but if you plan on adding 2" above an existing slab, I do not think you want to go with bagged concrete.

It will most likely crack, especially if...

I usually upload my photos to www.photobucket.com.

Then copy the image url and paste it into the message area.

http://i819.photobucket.com/albums/zz111/lacogada/phobuc_zps57bd820a.jpg

Picture would help.

http://i819.photobucket.com/albums/zz111/lacogada/roofleak_zps587180ba.jpg
Not faulty logic... but I do not understand why it makes it all the way down and only leaks ( it seems ) after its made it...

Thanks for that pdf... it will come in handy in the future as I plan to metal the whole roof, and do away with that flat roof.

Surface tension... I can see how water may back up at that 2"...

Pic to show bottom edge. Metal extends pass fascia approx 2"

http://i819.photobucket.com/albums/zz111/lacogada/botmetal_zps95021c4e.jpg

Never heard of surface tension, thanks advice and link.

Approx 5 bags at 80 lbs

smearcase... thanks for all your thoughts and suggestions.

The voids you mentioned are actually filled with custom cut pieces of cedar.
I cut the angle for the ridges and made some pretty descent...

Believe I follow what you're saying about shingle 1st & 2nd coarse.

I would say the flashing was 2" under 2nd coarse... top of flashing was not visible before putting tar.

In fact I had only...

Trying to find this leak for months.


Roof is approx 12'x 20'. Had a roll type roof made of rubber. Did not leak.
I decided to put metal above it anchored to 1 x 4 lats at 24" o.c.


I have a...

http://i819.photobucket.com/albums/zz111/lacogada/narrowbeam_zpsb3905a77.jpg

I may be able to draw up a sketch... but do not understand your explanation.

May need to give more details to get a reply.

http://i819.photobucket.com/albums/zz111/lacogada/2x4rafter_zps207a665f.jpg

Bracing is not an option ?

Thanks for the reply.

Trane heat pump.

What is the best way to clean this type of coil ?

http://i819.photobucket.com/albums/zz111/lacogada/TraneCoil_zps62f29b91.jpg

Maybe items below

Simpson Strong-Tie L50 Reinforcing Angles


Buy Right Angle Driver Bit Accessory at Woodcraft.com

Wheres the notch... what size beam ?


http://i819.photobucket.com/albums/zz111/lacogada/beamnotch_zps936221e4.jpg

http://i819.photobucket.com/albums/zz111/lacogada/wall2_zpse73bf8cf.jpg

http://i819.photobucket.com/albums/zz111/lacogada/walls_zps6013d3b0.jpg