Search:

Honda 3011 starts but dies when shifted into gear or if pto engaged

If it agitates, the motor is probably OK. Most likely the lid switch is defective.

You don't. Everything comes out through the front. Use a putty knife between the top and front panel to release the two clips that hold the top down and lift it up and tilt it back. From the inside...

Replace the water inlet valve assy.

You didn't say what brand. Some dryers have a thermal fuse that will not allow the dryer to come on if it is blown.

Top load washer:it's probably the lid switch
Front load: it:s probably the pump inlet clogged or the pump is bad

Sounds like the lid switch is not closing

The switch is located in the control panel. It is connected to the knob you use to select load size. There should be only one hose connecting the pressure sensor on the switch to the side of the tub...

The water level switch is a pressure operated switch. It has a tube (hose) that connects the switch to the bottom of the washer tub. If it comes loose or gets a hole in it it will cause the washer to...

If this machine has a separate pump from the drive motor, it could be the pump. Pump inlet clogged or drain hose clogged.

Could be the lid switch.

Probably the drum belt is off or broken.

Your house drain is slow. This allows water to back up and siphon the water from the tub. Create an air break where the hose enters the drain, and make sure the house drain is clear and flowing. Make...

You have to partially remove the rubber boot between the washer front and the tub, to access the door latch. There should be a spring holding a wire band tight around the outer edge of the boot...

Is there frost build-up in the lower back part of the freezer secttion? If so, the unit is not defrosting properly, either because the timer is not telling it to, or the defrost components are...

The coating is coming off the ice mold. You need to replace your icemaker, Or you could just replace the mold. A little cheaper but more work and skill required.

Check to see if the drain pump is pumping a full flow of water. Sometimes the inlet gets clogged with debris.

Simply put. The motor runs on 120 volt power and the heating element operates on 240 volts.

Replace the motor. About a $40 fix

If you cleaned the coils and its still running hot, make sure the little fan in the back by the coils you cleaned is running.

The switch that the know connects to. Its called and infinite switch.

Front load or top load?

Most of the components for this dryer are accessed from the front. Use a putty knife between the top of the bottom panel and door frame to release the spring clips that hold the bottom panel in place.

Your house drain is draining slow or the discharge tube is pushed down too far into the trap on the drain. The drain is siphoning the water out of the machine.

From the illustration it looks as though it is behind the toe-plate behind a small cover on the right-hand side.

Most likely the lid switch is broken.

Some of the Whirlpoolo built Kenmores have a thermal fuse on the back.

Sounds like the cold water side of your inlet valve is clogged or not opening properly. There should be a screen in the inlet of the valve that may be cleaned. Otherwise, the valve will have to be...

If the motor is not running or trying to run when you turn the dial to "spin" it is probably the lid switch or actuator

Sounds like the lid switch

If the motor is not running or trying to run in the spin cycle it's probably the lid switch. If the motor is trying to run, (humming, buzzing) it could be something lodged in the pump.
I would try...

How about the door switch?

You need a new timer. This is a whirlpool design and it has what is called a neutral pump-out where the motor runs and the pump pumps the water out but the tub doesn't spin. The timer is supposed to...

The ice door is the problem it should be solenoid opened and spring closed. Either the spring is broken or the solenoid is rusted. This is a common problem with certain GE side-by-sides..

If there is a lot of frost on the back wall of the freezer, (inside) it's not defrosting. The typical cause for this is the defrost heater. ( behind the back panel in the freezer at the bottom)...

There is a problem in the defrost system. If this is a GE built kenmore it is probably the defrost heater. Need the model number to tell the difference.

It sounds like your drain is syphoning the water out as it tries to fill. This is caused by a slow drain or an improperly installed drain hose. Make sure the drain hose is not pushed in to the drain...

Does it spin? Does it pump the water out?

If this is a frigidaire built kenmore, you may have to remove the drum to get to the element.

If its filling with the machine off you need new inlet valves. If it continues to fill and runs over only when it's trying to wash, it's either the fill level (pressure) switch or possibly a hole or...

Put some water in and see if it will agitate.
If it won't agitate, turn it to spin and see if it will pump the water out. If it won't agitate or spin but the motor runs and pumps the water out, the...

If the evaporator behind the panel inside the back of the freezer section is frosting top to bottom, the compressor and refr. Charge are usually OK. It sound as though you have a defrost problem and...

If this is a top freezer model, the water can be coming from one of two things.
1. Leaking refrig. Door gasket
2. the freezer drain is stopped up and water from defrost is overflowing into the...

It could be the water level switch. (pressure swith inside the console with the little hose connected to it).

Need more info. Complete model number would be helpful

Where can I find directions for replacing timing belt on a Mitsubushi Outlander, 2003 model. 4 cyl

The dryer will run if one of the fuses is blown or if one leg of the circuit breaker is tripped.
The fuses mentioned in the owners/operators manual are the ones for the residence not inside the...

...

If you can hear the motor runnilng it is the motor drive coupling.

You should be able to purchase the agitator dogs at any store that sells whirlpool or sears appliance parts.

The job is not to difficult. It requires removing and separating the agitator. The...