Ask Experts Questions for FREE Help !
Ask

Search:

Type: Posts; User: Stratmando

Search: Search took 0.15 seconds.

  1. Question: Central air

    by Stratmando
    Answers
    2
    Views
    83

    I wired one of my customers AC so if any...

    I wired one of my customers AC so if any Doors(could add windows, But they NEVER open) were open more that 5 Minutes it will shut off AC, so they are not Air Conditioning the Outside. Also, if Heat...
  2. Answers
    7
    Views
    226

    AND to the sides of the box. Good Luck

    AND to the sides of the box. Good Luck
  3. Question: A/C

    by Stratmando
    Answers
    3
    Views
    76

    Just match up the uF(Microfarads), and the...

    Just match up the uF(Microfarads), and the Voltage, Replacement can have a higher voltage, Be accurate on the uF. May have 3 terminals, pay attention to where the wires are connected, If it has 3...
  4. Answers
    7
    Views
    226

    Whoever does the Backsplash, especially if it Is...

    Whoever does the Backsplash, especially if it Is Marble or Granite for them to cut up to the sides of the box, and so the 2 screws can be inserted. See some who cut openings screws will not go in or...
  5. Answers
    3
    Views
    100

    Try new Batteries, or removing and reinsert...

    Try new Batteries, or removing and reinsert Batteries.
  6. Answers
    3
    Views
    102

    I think Batteriesplus also has individual...

    I think Batteriesplus also has individual Batteries, See if you can open pack without damage.
  7. Try new Batteries, or removing and reinsert...

    Try new Batteries, or removing and reinsert Batteries.
  8. The WD 40 was not for lubrication, it was to...

    The WD 40 was not for lubrication, it was to release the junk then blow out. Brake Kleen would surely Remove all. Then use a DRY Lubricant, Would wipe a coating of WD on the face of the lock(The...
  9. Answers
    6
    Views
    192

    Just to mention, If they were wired in Series,...

    Just to mention, If they were wired in Series, All Bulbs would have too work, if one bulb was broke or removed, others would not light.
  10. Spray down with WD 40 or something, wipe down, if...

    Spray down with WD 40 or something, wipe down, if it operates fine, keep it. Better than being dry. May not have wanted the Bright Brass to Tarnish.
  11. Question: Honda Accord

    by Stratmando
    Answers
    1
    Views
    115

    I would check Fluid, and change Tranny Filter,...

    I would check Fluid, and change Tranny Filter, Can't hurt, and may show little or lot of metal flakes.
  12. Answers
    7
    Views
    226

    The old way was to just take a hammer and break...

    The old way was to just take a hammer and break out the block behind it. If on a web, you can move over a little so it falls within a cell. Better is to take a Die grinder and cut out for the boxes,...
  13. Answers
    5
    Views
    232

    2 Common ways is T&M(time and materials), Not to...

    2 Common ways is T&M(time and materials), Not to be confused with T&A.
    I charge my Hourly and add 20% to Materials. I give Customer the option to buy the Materials, Need to get paid for my Time....
  14. Answers
    7
    Views
    165

    What did you find with Fuel Pump, and Regulator?

    What did you find with Fuel Pump, and Regulator?
  15. Answers
    1
    Views
    141

    Some have Throttle slides with 1 cable, some have...

    Some have Throttle slides with 1 cable, some have 2 cables, a pull and a push cable. Be sure routing does not affect Throttle Operation while turning handlebars.
    Can you describe more what you have?...
  16. Answers
    7
    Views
    165

    If You have no Manual, and you are cranking...

    If You have no Manual, and you are cranking Engine during test, 2 things you could do, Hook a wire to fuel Pump wire at fuel pump, add test light, when you jump the relay, or provide power in relay...
  17. Answers
    23
    Views
    306

    Certified doesn't always mean Competent or...

    Certified doesn't always mean Competent or Qualified. Change the Board and see if that is it? We call them Board Changers. I would do some testing before Buying a Board, Many are quick and Cheap...
  18. Answers
    23
    Views
    306

    Just a Note, If you don't hear door switch, it...

    Just a Note, If you don't hear door switch, it may be bad. Hearing it does not mean it is working or wires didn't come off switch.
  19. Spy Vs Spy?

    Spy Vs Spy?
  20. Answers
    6
    Views
    9,504

    You need a Neutral AND Ground. Ground is Not to...

    You need a Neutral AND Ground. Ground is Not to carry Current, If you did have a ground and Neutral, a Red and Black can Share a Neutral(a Multi Circuit), they need to Be Next to each other on Panel,...
  21. Answers
    3
    Views
    112

    On the 14' sides, if using 4' wide sheets, It...

    On the 14' sides, if using 4' wide sheets, It would take 4 to do 1 side, with 2' left over, you can use that 2' piece on other side. Which equals 7 sheets.
    For the Long side it would take 20 sheets...
  22. Question: Rectifier help

    by Stratmando
    Answers
    1
    Views
    103

    Old Rectifier may not work, Most I have worked...

    Old Rectifier may not work, Most I have worked with have 3 yellows(or other)from Stator, these Put Out AC Voltage, Going through a rectifier is usually 6 diodes, 2 for each yellow, 1 passes the...
  23. Answers
    7
    Views
    165

    You don't mention Fuel Pump Relay. I would get...

    You don't mention Fuel Pump Relay. I would get the Service Manual and follow the Fuel Pump On back. My Ford Truck has an Inertia Switch, so if there is Impact, It Interrupts power to Pump. Just need...
  24. Answers
    23
    Views
    306

    With power off you can check for continuity on...

    With power off you can check for continuity on the thermals, usually on the ductwork.
  25. Answers
    1
    Views
    99

    It would be Float sticking, or need adjusting,...

    It would be Float sticking, or need adjusting, Float Needle. Or debris keeping Float Needle from closing. If you dissemble, do not bent float parts, and be sure float is not hanging up on the side.
  26. Answers
    23
    Views
    306

    Wonder if it is contacts on timer, or Centrifugal...

    Wonder if it is contacts on timer, or Centrifugal switch?

    Even a failing door switch?
  27. Answers
    23
    Views
    306

    I find it is Usually 1 Part that goes Bad, Some...

    I find it is Usually 1 Part that goes Bad, Some are Cheap, others Expensive,
    If Capable, you need to Start at the receptacle, then follow the power in to the Dryer. Does the Door Switch click when...
  28. Sure hope she Recovered?

    Sure hope she Recovered?
  29. Answers
    8
    Views
    184

    Does the whole Wiring Harness need to be sorted...

    Does the whole Wiring Harness need to be sorted out? Swaping an engine only needs a few connections. The New Engine will have most of these to deal with. Wiring from the Stator to generate...
  30. I checked that out, can Only Order, No Reviews,...

    I checked that out, can Only Order, No Reviews, no Info? Customer found something else, should see Friday what he got, Thanks
  31. Answers
    3
    Views
    132

    I would draw a Circle actual scale, then Lines...

    I would draw a Circle actual scale, then Lines through it every 1/16", Figure how you want to attach, at the corners? or a little overlap to increase strength?
    Good Luck
  32. Remote unforward Comcast Voicemail Remotely?

    I have a Customer that wants to reboot Comcast modem when it loses Internet, He says when it happens, he usually has his VOIP still working. So, I wanted to use a Viking Electronics RC2a Touchtone...
  33. Vet for sure, did she eat a bone? If so, may be...

    Vet for sure, did she eat a bone? If so, may be lodged causing discomfort in certain positions. I would maybe get her to Vet with Minimal Movement to prevent further damage? Wouldn't make her walk....
  34. You could put an Amprobe on the wires at the...

    You could put an Amprobe on the wires at the Water Heater. You will see if it is even Heating, and when it is not, Some of those use Thermals you can buy at an Auto part store that sometimes fail,...
  35. If you have a Right angle that goes up 3', and...

    If you have a Right angle that goes up 3', and across 4', and want to find the length of the angled side. You would square the 3, which is 9. The square the 4, which is 16. Then add the two, 9+16=25,...
  36. Answers
    5
    Views
    144

    Each of the 3 lights black wires needed to be...

    Each of the 3 lights black wires needed to be connected to 1 of the switch wires, the other switch wire from power/switchleg, If wired like that and lights don't go off, it is a bad light switch.
  37. Answers
    6
    Views
    192

    May have been wired correctly, in 1 light and out...

    May have been wired correctly, in 1 light and out to next light may seem series, but actually wired Correctly(in parallel). Need to see if you have power out of switch, then see if you have power to...
  38. Answers
    5
    Views
    144

    Your light switch may have 2 black wires, 1...

    Your light switch may have 2 black wires, 1 connects to power coming down through fan, the other black on switch connects only to each of the sockets black.
  39. 3+4+7=?

    3+4+7=?
  40. Tough Kid, didn't scream with the Heated Band,...

    Tough Kid, didn't scream with the Heated Band, but did when it shrunk?
    Doesn't sound familiar, will Google more later
  41. Answers
    4
    Views
    165

    What good is a Spare? Usually New Spare Push...

    What good is a Spare? Usually New Spare Push Button Switch should work. Please don't carry a Broken Spare Switch. Do you feel that Switch is the Next/First thing to fail. They Must have a high...
  42. Try turning off water, then Electric, then...

    Try turning off water, then Electric, then circuits 1 by 1 to further locate if electrical.
  43. Answers
    4
    Views
    165

    May be similar to an Ignition Switch Failure....

    May be similar to an Ignition Switch Failure. Repairing is the solution. Bypassing and overriding is possible. Do they have a high failure rate. Google your vehicle and Push button start failure, see...
  44. Answers
    2
    Views
    169

    Rusted? Corroded? Bolt Head Stripped? Awkward...

    Rusted? Corroded? Bolt Head Stripped? Awkward Position? Frozen solid and won't turn? Remove bolts that you can first. Good Luck
  45. Should be a Nameplate showing Watts/Amps, and/or...

    Should be a Nameplate showing Watts/Amps, and/or recommended size of Breaker.
  46. Most of their fans have blades can be installed...

    Most of their fans have blades can be installed either way. If blades have any wording or numbers by mounting holes, they usually face up. When you say Leading edge like an Airfoil, if so, Bigger end...
  47. There is a way you could do with Modules at each...

    There is a way you could do with Modules at each light, and have separate switches for each.
  48. Answers
    5
    Views
    219

    I see now

    I see now
  49. Answers
    5
    Views
    219

    Can you explain a little, trying to understand?...

    Can you explain a little, trying to understand? If Start/Stopped Button was pressed while driving it would die, Not good, A Safety feature.
    Are you wanting to open the door while engine running?...
  50. Question: Power source

    by Stratmando
    Answers
    4
    Views
    200

    What did you Figure? Thanks

    What did you Figure? Thanks
Results 1 to 50 of 500