Search:
Type: Posts; User: stuartn
Search:
Search took 0.00 seconds.
-
Did you take the pump off and check to see if something is stuck in it? This would not explain the broken coupler but it is free and easy to check. A plugged pump would give you these symptoms. ...
-
-
The drain hole is frozen or plugged. Take the shelves out of the freezer and take the panel at the back off. There should be a hole that the water drains into. Use hot water to clear the hole. Do...
-
You took off the wires to the thermostats on the heater housing. With out a model number I can not tell you what colors go to where. If this does not look the same then do not do this hook up. ...
-
Having never moved a furnace before I hope this is not a dumb question. I need to move a used furnace about 2 hours in a mini van. Can it be laid on its back/side or will that cause pieces inside...
-
You have a timer problem if the timer does not turn off on the time cycle. This may or may not cause the heating problem. It still could be the element or thermostats.
-
Does the timer turn off on a time cycle? If it does then it is most likley a heating element problem. Unplug the dryer and remove the back panel. On the bottom right side there will be your...
-
You may have a door switch problem. It sounds like the dryer does not recognize that the door is closed and beeps to tell you it is open. (Grey?) button near the top of the door opening.
-
Replace the console/touchpad.
-
There is a part in the transmission that is worn out. There is a kit to repair it but it is easier and quicker just to replace it. Is it your motor that is clicking? It should not make any...
-
Your house venting is plugged or restricted. Clean your venting or replace it. Also make sure you dryer is not pushed back to far and restricting the vent. This causes your thermal fuse to open...
-
You have a defrost problem. Check the defrost element to see if it is broken using an Ohm meter. If there is continuity then check the defrost thermostat with your Ohm meter(must be cold to be...
-
The compressor sits on 3 springs inside the can. One of the springs is broken so when it stops it bangs against the side. The compressor itself should work fine as long as you can put up with the...
-
The machine has a fill error. If the right amount of water does not come in during the proper time allowed then it will give you an FH code. Try a rinse cycle that uses cold water to see if you get...
-
What ever you put in your machine is the only thing it can be. Laundry soap does not sud unless there a LOT of it. If you have soap or something on your clothes from something else then it will...
-
You may need a new lid switch.
-
You have a cold control problem and should be replaced.
-
There should be an access panel on the front below the door. Remove this and on the inside walls there should be tech papers on how to put it in test mode. Good luck.
-
Find the wires that run to the glow bar under the floor. May have access if you remove the bottom drawer or remove the floor of the range. 2 tabs or screws at the back that lock the floor into...
-
There is a fuse attached to the plastic housing of the board in the control panel. 2 wires going to it. Check with an ohm meter. Turn power off to do this. New one comes as a kit. Follow the...
-
Your dryer will have a pilot light if it is older than 20. The newer dryers have a glow bar. (The rest is assuming that you have a newer dryer because you do not provide a model number to...
-
You may have something in your pump. If you do not have the water out yet you should take out as much as you can. Tip the washer back so you can access the underside. The pump is held on the front...
-
If you have water and clear screens then it should be a water valve.
-
The breaker is in the panel on the house. Double 30A is what it will be. Kenmore brand is be made by several companies all with different styles of dryer. What is the model number?
-
Check your breaker first. Turn it off and then on. If half of the breaker is tripped then it will run with no heat. Your element could be broken also.
-
GE dryers access from the front. Open the door and the screws are on the underside of the lip, facing up to hold the top to the front. Remove the top. Then the front comes off with 2 screws that...
-
Are the dishes clean? Make sure there is enough water. With it in wash open the door quickly to see if both wash arms are turning. If the soap door is opening during the cycle then it is a washing...
-
What make and model do you have?
-
Clean the screens on the water valve where the hose from the house meets the machine. Do not take the screens out. Just clean them in place (with a old toothbrush or something like that).
-
It could be the start windings in the motor that are the problem. Replace the entire motor.
-
Room temp is important. The cold control is in the fridge part(not the freezer) and it tries to reach about 4C(depending on where the dial is set). If the ambient air temp is about the same then...
-
If the pressure switch is reading that there is too much water in the machine(overflow situation) then it will turn on the pump. Take the top off and find the pressure switch. Take the hose off to...
-
Make sure the icemaker is calling for water. You should be able to hear the water valve for about 5-8 seconds when it calls for water. The line that feeds the icemaker may be frozen where it goes...
-
Can you restart the dryer right after it turns off do you have to wait for a while? If you have to wait a while (1/2 hour or longer) then you may have a motor problem. You said that is bogs down...
-
What is your model number? Open the door and look for the tag.
-
Start by looking at the rollers. Two screws on the front. 4 rollers total so try to narrow it down.
-
Whirlpool dryers do not have rear bearings so do not look for one.
-
Also test the defrost thermostat. If the heater and thermostat both test good the replace the defrost timer.
-
You should check the Maytag repair site. Your fridge may qualify for the Maytag recall. Your model number starts with MS which is a qualifying model number. You need to check your serial number...
-
You need 220V across the flats on your plug (Red and Black) and 120V across the rest. Turn your breaker off and then on. Twice if you like. It will be a double 30A and it may not look tripped so do...
-
You may have something caught in the blower. The motor is drawing too much current and is tripping the overload built into the motor. Take the back off and remove the blower housing on the left...
-
There is a 1 year warranty with #2 so get it fixed by someone that knows and for free.
-
-
Try to spin with no clothes in it. If it does not spin any better then you may have something between the inner and outer tub. You can take the tub ring off and look down between the tubs. If it...
-
Does the lid switch click when you open and close the lid?
-
Try to turn the tempature up in the freezer a little so it does not get that cold in the fridge.
-
Check the coupler between the motor and transmission.
-
Did you test for continuity or voltage? Do you get power to the inline fuse or to the door switches? Have you checked the electricial box underneath to make sure that good connection is being made...
-
JSkip- Take your model number to the local appliance store that deals with your brand and ask for a stacking kit. Follow the instructions. Nothing eletricial needs to be changed.
-
It will say in the owners manual if there is one and where it is.
|