Search:
Type: Posts; User: hixton
Search:
Search took 0.01 seconds.
-
Did you clean the flame sensor?
-
That 1" square shroud comes off some are welded then you just pull it out and then push one back in
-
Does the flame move when the blower kicks on ?
-
The exact ohms vary from unit to unit check to see that you have a resistance and that its not grounded
-
Sounds like you might be lucky do the pipes run through the roof or out the side wall check the ends of the pipes also check your drain sometimes that will plug and give you the same code
-
Check the gas pressure and did you clean the pilot or the burner
-
Call your dealer back there should be a warranty on the work they did it sounds related is the thermostat digital or mercury
-
Try turning the power no off to the furnace when the humidifier is running it will reseat the solenoid
-
Check to see if the fuse is blown on the board in the blower compartment
-
There is a alarm for the attic fan in side the furnace right in the middle there is a switch you can shut the beeping off then have it checked out later
-
Have you cleaned your vent pipe lately ? If not try that also clean the lint trap with a brush and soap and water.
-
It sounds like like you need new solenoids on the firing valve
-
-
Yes don't run it until you get it checked out it could be low gas pressure or the burner is dirty or the firing valve isn't seating off all the way there's a good chance it's making carbon monoxide.
-
-
-
The second question try cleaning you drain hose that's right above the furnace shut the furnace off then let it dry before trying it again make sure the hose all the way to the drain is clean if it...
-
Replacing your thermostat is right
-
Try replacing the batteries in the thermostat
-
The sensor is dirty remove and clean with a brillo pad it is usually is located on the left side of the burners
-
-
You should call your electric company its what they call part power you may have a line fuse blown.
-
Do you have the right size capacitor for the motor? You can go up 10% for a run but you can't go lower on a run capacitor. If they won't last you will have to replace the motor.
-
Have you tested the capacitor to see if that's what bad it could be a dead spot on the motor.
-
Try cleaning the sensor that's the rod in the flame if that doesn't work you may need a tech to look at it .
-
-
That smell by Lynyrd Skynyrd
-
The firing valve is the main control that allows gas into the furnace the pick and hold is the way the valve on a bryant furnace works it the way they design it . Troubleshooting should be left to a...
-
Many things from control boards to ignitors being bad to open limits to name a few
-
-
John it could be your firing valve the pick and hold might not be working right give that a try
-
It sounds like your contactor on the unit outside is stuck closed you should have it check if it is that is a cheap fix
-
It quits while driving then has to be jumped started
-
1997 dodge stratus won't stay running replaced battery and alternator still won't stay running
-
Pull the hose off and blow through it then check where connects to see if there is anything
Inside the connection
-
First you need to establish who the dominant one is you should place your puppy on her back and hold her firmly until she submits don't let her push you around don't let her stop when you are going...
-
-
Have you had anyone check for a gas leak
-
Hook one to r and one to w
-
Sounds like a herniated belly button check with your vet it can be or it might be nothing depends on the size I hope this helps
-
Has the furnace ran this year or is this the first time ?
-
Take the front off there is a rest button on I think the upper left you have to push I think it's a black button on the base plate
-
-
You might want to check your local building codes first it might not allow what you want to do
-
Check the belt it be broke or off
-
There could be a few different things wrong it could be a dirty sensor a drain could be plugged to name a couple you should call a dealer that services that brand and have them take a look at it
-
Does it try to start is the flame real small on the pilot you might have a rusted pilot orifice
-
Yes they do but if you take him back he will always think that you are going to cheat on him sorry to say this but move on before its to late it was his choice get on with your life its to hard to...
-
Did you shut it off and turn it back on and did you try cleaning the sensor
-
You need to check to to see if your high voltage transformer is working as if you bled all the air out I am assuming that you are getting fuel the next step is to check for ignition if you have no...
|