Ask Me Help Desk

Ask Me Help Desk (https://www.askmehelpdesk.com/forum.php)
-   Appliances (https://www.askmehelpdesk.com/forumdisplay.php?f=157)
-   -   Whirlpool washer agitates, but won't spin with full load (https://www.askmehelpdesk.com/showthread.php?t=266507)

  • Oct 5, 2008, 04:12 PM
    cojulun
    Whirlpool washer agitates, but won't spin with full load
    I have a Whirlpool Ultimate Care II Quiet Wash I washing machine, Model #LSB6400LW1. The washer agitates fine, and but will not spin with a medium load WITHOUT my reaching in to the washer and helping it get started (by twisting the inner basket like a roulette wheel).

    With a full load (it is a Super Capacity washer), the unit will not spin at all, even by helping it to get started.

    I have a couple hypotheses, but would rather first hear from a professional repair person or someone else who has had this same issue on what could be causing the "spoin with help, but no spin with full load" syndrome. Thanks!
  • Feb 16, 2010, 09:25 AM
    Shelly_Denise
    I'm having the same problem now. It started yesterday. I overloaded the washer because I was in a hurry and when it started in the spin cycle I could smell a hot-motor-oil smell. I had stop the washer and take some of the soaking wet clothes out and start the spin manually. I've washed another load since then and I had to reach in to start the spin again. So I'm sure something is broke or stripped. I'll have to get back on the model number because I haven't checked yet, but it's a top load Whirlpool.
  • Feb 17, 2010, 11:49 PM
    Flying Blue Eagle

    COjulun-ON the washer what may of happened is -the belt could have streached from the belt getting hot or may be broken,There are about (7) reasons for this to happen solets start with this cause first; #1- unplug the power cord,disconnect the water lines,hot and cold, make sure the tub has NO water in it!! ;;next pull washer out from the wall, #2- Lay washer down on the floor; front side first ' find the motor and in between the motor and the pulley ,with your thumb center ways between motor and pully ,push inward with thumbthe belt, {NOTE} there should be NO MORE THEN 3/4in defelection from stright;IF belt is not broke; BELT is loose and slipping;; to tighten the belt to factory settingsWITH A WRENCH,loosen the mounting bracket nut,after losing nut SHIFT THE MORTOR POSITION#3- to tighten the belt to is proper factory setting;; You may have to loosen and tighten the mounting bracket 2or3 times to get as close as possible,to the proper settingremember that the proper setting of the belt is 3/4"defeliction in center between motor and pullyretighten the mounting nutset machine back up right and try it out if not then tomorrow wwe can try one of thr six others;;We will need a VOLT -OHM meterto do some testing ;IF you don't have one you can get one for less then {$16.00 dollars at Lowe's< OR HOME DEPOT IN THERE ELECTRICAL DEPT. If this don't work ,then we will go to the next ste I will be waiting for your reply here on this pos Have a great day and GOD BLESS ;;F.B.E.
  • Dec 2, 2011, 07:07 AM
    john9900011
    Some machines won't spin with a heavy load or excess water (Quilt) they are designed this way so they don't break!
  • Nov 7, 2012, 08:11 AM
    wayne king
    The agitator is in 2 pieces bottom work OK top doesn't

  • All times are GMT -7. The time now is 09:40 AM.