Ask Experts Questions for FREE Help !
Ask
    mrcleene's Avatar
    mrcleene Posts: 1, Reputation: 1
    New Member
    		  
    #1

    Sep 9, 2009, 08:46 PM
    Program sears keyless garage door opener
    I have a sears model #139.53684 how do I program it to open garage door. I need to put in a new code the original code was lost
    Thank you!
    Fix-er-rite's Avatar
    Fix-er-rite Posts: 3, Reputation: 1
    New Member
    		  
    #2

    Sep 9, 2009, 10:39 PM
    Hello,
    I will need to ask you some more questions. How old is the keyless entry? Does it light up when you press any buttons? What type of battery does it have? How old is the machine hanging from the ceiling? Is it a Craftsman opener? Does it have a block of switches on a circuit board near the back of the opener? Do you see any red, green or purple square buttons? How about yellow, white, green circular buttons? What colour antennae does it have? You might have to remove possibly a light cover. Do not remove any screws. May sound sort of daunting. It is an easy fix but with out seeing it you have to be my eyes!You could also send me some photos if you wish. You can get back to me here or email me at [email protected], visit my website at Garage Door Repairs | Canyon Springs Overhead Door, Vancouver, BC or call me toll free at 1 877 931-2777. The regular number here is 604 945-7595.
    Hope this helps
    Brad
    Timaaay's Avatar
    Timaaay Posts: 2, Reputation: 1
    New Member
    		  
    #3

    Oct 14, 2012, 02:52 PM
    I see this thread it a few years old, but I had a difficult time finding the CORRECT way to program this remote. There are a few sites that give the wrong programming of the Sears 139.53684.
    There are two ways: First, if you remove the light cover you will see an orange learn button. Press this button (DO NOT HOLD OR IT WILL ERASE ALL MEMORY) and an LED should light. Within 30 seconds, enter your new 4-digit code on the 139.53684 and hold the "ENTER" button until the light on the motor flashes. New code is learned!

    Method two:
    If you have a multi-control on your wall as an opener (with a light button) enter the new the new 4-digit code on your 139.53684 and hold the "ENTER" button, while holding the enter button press and hold the light button. Continue holding the enter and light buttons and press the "open bar" (You're holding ALL three buttons now) when the light on the motor blinks, release all buttons and your new code is programmed.
Not your question? Ask your question View similar questions
 

Add your answer here.


Check out some similar questions!

Sears craftsman garage door openeer keyless entry [ 4 Answers ]

I have a sears craftsman 1/2 garage door opener with keyless pad, the keypad does not work when you enter code. Batteries have been changed and I do not see a lean button on it. Any ideas?

Craftsman garage door opener keyless entry forgot code [ 3 Answers ]

Have a craftsman garage door opener with keyless entry. It's approx 7 yrs old and I can't remember the code to open the door. Need help so that kids can come in and out without having to take a key. Any help is appreciated

How do I sync the keyless pad garage door opener to the main garage door opener? [ 3 Answers ]

I mistakenly gave someone my garage door opener that didn't return it. I had a male friend come over and "change the code" including my car opener and gave me a universial which he also programmed. I came to realize my code for my keyless pad outside doesn't work (since he changed the code... )....

Sears garage door opener [ 6 Answers ]

I have a sears garage door opener. When it gets cold, the door will not close unless I hold the wall switch down until it closes to the ground. When the weather gets above 40 degrees, then it works fine. Any idea on what is causing this? I have tried to adjust the opener but it doesn't help.

Garage door opener keyless entry reset [ 1 Answers ]

How do I reset the keyless entry password on my garage door opener? It's a craftsman 1/3hp, model # 139.23325SRT.

View more questions Search