Ask Me Help Desk

Ask Me Help Desk (
-   Cars & Trucks (
-   -   Reset computer in 1993 toyota camry (

  • Dec 8, 2012, 08:34 AM
    Reset computer in 1993 toyota camry
    Just changed alternator but I had no power going to switch. Found a burned out fuse (100 amp ALT). I replaced it and got power to switch, all warning lights now came on but starter still will not turn over. Appears to have no power to starter. How can I check power to starter and if not what then?
    1993 toyota camry
  • Dec 8, 2012, 09:03 AM
    I am not a mechanic, but if you blew a fuse, there has to be a problem. See if there is power to the syliniod (I don't think I spelled that right;) ).Maybe that is the problem that burnt the fuse to begin with. If you have power going that far then it is. Hoping that your vehicle has it separate from the starter.
  • Dec 8, 2012, 09:09 AM
    By the way, to check for power to the starter, just disconnect the starter wire from the starter. Have someone turn the key and check the wire for power using an ohms meter or just a simple continuity tester light will do. If no power there, then back to the last step.
    To check your starter, remove the starter and check with booster cables, which you probably know.
  • Dec 8, 2012, 09:19 AM
    Starter Motor Won't Crank

    . Ensure the battery is fully charged, before diagnosing starter problems. Then, test each cell, with a hydrometer or multimeter, to ensure that it's good. This important step is often overlooked.
    . Test all under hood and under dash fuses with a test light or multimeter.
    . Ensure the gearshift is in Neutral or Park (automatic transmission), or the clutch pedal is depressed (manual transmission), if the starter motor does not turn at all when the ignition switch is turned to Start.

    1. If the starter motor doesn't turn, but the starter solenoid (relay) "clicks" when the ignition switch is turned to Start, the problem is with the battery, starter solenoid, or starter motor connections.

    2. Disconnecting the negative battery cable first, clean battery terminals and cable connections with a battery terminal brush, No. 240 abrasive cloth, or steel wool. Also, check the battery ground cable connection to the body and engine. Apply silicone dielectric grease, when finished. Examine the cables carefully for hidden corrosion or internal breaks.

    3. While the negative battery cable is disconnected, clean starter motor and starter solenoid connections. Apply silicone dielectric grease, when finished. Make sure all connections are secure. When installing the starter cable, make sure that the crimped side of the ring terminal is facing out. Reconnect the negative battery terminal last.

    4. If the starter motor spins but the engine is not cranking, the overrunning clutch in the starter motor is slipping and the starter motor must be replaced. Also, the ring gear on the flywheel or drive plate may be worn.

    5. If the solenoid plunger cannot be heard when the switch is actuated, the battery is bad, the fusible link is burned (circuit is open), or the solenoid is defective.

    6. In order to check the solenoid, put the transmission in Park and remove the push-on connector from the solenoid S terminal. Connect a jumper lead (12 AWG), or preferably a remote starter switch, between the positive battery terminal and the exposed S terminal on the solenoid. If the starter motor now operates, the solenoid is fine and the problem is with the ignition switch, neutral start switch, or wiring. If the starter motor still does not operate, replace the solenoid.

    7. If the starter motor cranks the engine slowly, ensure the battery is fully charged and all terminal connections are clean and tight. Then, check connections at the starter solenoid and battery ground. The engine will also crank slowly, if it's partially seized or has the wrong viscosity oil in it. Synthetic engine oil allows starter motors to turn the engine over easier and faster, thus promoting starting and reducing battery drain.
  • Dec 11, 2012, 01:54 PM
    When the 100A Alt fuse pops, you can bet the bank it took more fuses out with it. All of the under dash and under hood fuses need to be checked with a test light.

  • All times are GMT -7. The time now is 11:45 AM.